相关论文: Cusp Points in the Parameter Space of Degenerate 3…

This paper investigates the existence conditions of cusp points in the design parameter space of the R\underline{P}R-2P\underline{R}R parallel manipulators. Cusp points make possible non-singular assembly-mode changing motion, which can…

This paper investigates the cuspidal configurations of 3-RPR parallel manipulators that may appear on their singular surfaces in the joint space. Cusp points play an important role in the kinematic behavior of parallel manipulators since…

This paper presents an algorithm for detecting and computing the cusp points in the joint space of 3-RPR planar parallel manipulators. In manipulator kinematics, cusp points are special points, which appear on the singular curves of the…

This paper investigates the singular curves in the joint space of a family of planar parallel manipulators. It focuses on special points, referred to as cusp points, which may appear on these curves. Cusp points play an important role in…

This paper investigates the singular curves in two-dimensional slices of the joint space of a family of planar parallel manipulators. It focuses on special points, referred to as cusp points, which may appear on these curves. Cusp points…

Cusps and nodes on plane sections of the singularity locus in the joint space of parallel manipulators play an important role in nonsingular assembly-mode changing motions. This paper analyses in detail such points, both in the joint space…

The aim of this paper is to classify one family of 3R serial positioning manipulators. This categorization is based on the number of cusp points of quaternary, binary, generic and non-generic manipulators. It was found three subsets of…

We study in this paper a class of 3-RPR manipulators for which the direct kinematic problem (DKP) is split into a cubic problem followed by a quadratic one. These manipulators are geometrically characterized by the fact that the moving…

The workspace topologies of a family of 3-revolute (3R) positioning manipulators are enumerated. The workspace is characterized in a half-cross section by the singular curves. The workspace topology is defined by the number of cusps that…

This paper proposes a new design method to determine the feasible set of parameters of translational or position/orientation decoupled parallel robots for a prescribed singularity-free workspace of regular shape. The suggested method uses…

Having non-singular assembly modes changing trajectories for the 3-RPS parallel robot is a well-known feature. The only known solution for defining such trajectory is to encircle a cusp point in the joint space. In this paper, the aspects…

This paper presents the kinematic analysis of the 3-PPPS parallel robot with an equilateral mobile platform and a U-shape base. The proposed design and appropriate selection of parameters allow to formulate simpler direct and inverse…

A classification of a family of 3-revolute (3R) positioning manipulators is established. This classification is based on the topology of their workspace. The workspace is characterized in a half-cross section by the singular curves of the…

This paper deals with the comparison of planar parallel manipulator architectures based on a multi-objective design optimization approach. The manipulator architectures are compared with regard to their mass in motion and their regular…

When moving from one arbitrary location at another, a parallel manipulator may change its assembly-mode without crossing a singularity. Because the non-singular change of assembly-mode cannot be simply detected, the actual assembly-mode…

A class of analytic planar 3-RPR manipulators is analyzed in this paper. These manipulators have congruent base and moving platforms and the moving platform is rotated of 180 deg about an axis in the plane. The forward kinematics is reduced…

This paper investigates a situation pointed out in a recent paper, in which a non-singular change of assembly mode of a planar 2-RPR-PR parallel manipulator was realized by encircling a point of multiplicity 4. It is shown that this…

This paper investigates two situations in which the forward kinematics of planar 3-RPR parallel manipulators degenerates. These situations have not been addressed before. The first degeneracy arises when the three input joint variables r1,…

A classification of a family of 3-revolute (3R) positining manipulators is established. This classification is based on the topology of their workspace. The workspace is characterized in a half-cross section by the singular curves. The…

This article synthezises the most important results on the kinematics of cuspidal manipulators i.e. nonredundant manipulators that can change posture without meeting a singularity. The characteristic surfaces, the uniqueness domains and the…