相关论文: Triple Scissor Extender: A 6-DOF Lifting and Posit…
A new type of parallel robot mechanism with an extendable structure is presented, and its kinematic properties and design parameters are analyzed. The Triple Scissor Extender (TSE) is a 6 Degree-Of-Freedom robotic mechanism for reaching…
A novel kinematically redundant (6+3)-DoF parallel robot is presented in this paper. Three identical 3-DoF RU/2-RUS legs are attached to a configurable platform through spherical joints. With the selected leg mechanism, the motors are…
The previously introduced aerial manipulation systems suffer from either limited end-effector DOF or small payload capacity. In this dissertation, a quadrotor with a 2-DOF manipulator is investigated that has a unique topology to enable the…
This paper presents a unified algorithm for motion and force control for a six degree-of-freedom spatial manipulator. The motion-force controller performs trajectory tracking, maneuvering the manipulator's end-effector through desired…
Robotic arms are key components in fruit-harvesting robots. In agricultural settings, conventional serial or parallel robotic arms often fall short in meeting the demands for a large workspace, rapid movement, enhanced capability of…
Various 6-degree-of-freedom (DOF) and 7-DOF manipulators have been developed to date. Over a long history, their joint configurations and link length ratios have been determined empirically. In recent years, the development of robotic…
Multi-degree of freedom robots are playing very important role in different applications of automation. They are providing much more accuracy in carrying out a typical procedure as compared to the manual work done by human. In recent years…
An effective method for optimizing path planning for a specific model of a 6-degree-of-freedom (6-DOF) robot manipulator is presented as part of the motion planning of the manipulator using computer algebra. We assume that we are given a…
This paper introduces a rescue robot named Sigma 3 which is developed for potential applications such as helping hands for humans where a human can not reach to have an assessment of the hazardous environment. Also, these kinds of robot can…
We propose an effective method for solving the inverse kinematic problem of a specific model of 6-degree-of-freedom (6-DOF) robot manipulator using computer algebra. It is known that when the rotation axes of three consecutive rotational…
Aerial manipulators, which combine robotic arms with multi-rotor drones, face strict constraints on arm weight and mechanical complexity. In this work, we study a lightweight 2-degree-of-freedom (DoF) arm mounted on a quadrotor via a…
This paper introduces a new surgical end-effector probe, which allows to accurately apply a contact force on a tissue, while at the same time allowing for high resolution and highly repeatable probe movement. These are achieved by…
This paper presents Delta6, a low-cost, six-degree-of-freedom (6-DOF) force/torque end-effector that combines antagonistic springs with magnetic encoders to deliver accurate wrench sensing while remaining as simple to assemble as flat-pack…
Robot-assisted fruit harvesting has been a critical research direction supporting sustainable crop production. One important determinant of system behavior and efficiency is the end-effector that comes in direct contact with the crop during…
This chapter is about the fundamentals of fabrication, control, and human-robot interaction of a new type of collaborative robotic manipulators, called malleable robots, which are based on adjustable architectures of varying stiffness for…
This thesis introduces a novel quadrotor manipulation system that consists of 2-link manipulator attached to the bottom of a quadrotor. This new system presents a solution for the drawbacks found in the current quadrotor manipulation system…
Scissor lifts, a staple of mechanical design, especially in competitive robotics, are a type of linkage that can be used to raise a load to some height, when acted upon by some force, usually exerted by an actuator. The position of this…
Parallel robots are capable of high-speed manipulation and have become essential tools in the industry. The proximal placement of their motors and the low weight of their end effectors make them ideal for generating highly dynamic motion.…
We address a class of manipulation problems where the robot perceives the scene with a depth sensor and can move its end effector in a space with six degrees of freedom -- 3D position and orientation. Our approach is to formulate the…
To enlarge the translational workspace of cable-driven robots, one common approach is to increase the number of cables. However, this introduces two challenges: (1) cable interference significantly reduces the rotational workspace, and (2)…