相关论文: Stability analysis through folds: An end-loaded el…

The application of variational principles for analyzing problems in the physical sciences is widespread. Cantilever-like problems, where one end is fixed and the other end is free, have received less attention in terms of their stability…

The nonlinear mechanics of a flexible elastic rod constrained at its edges by a pair of sliding sleeves is analyzed. The planar equilibrium configurations of this variable-length elastica are found to have shape defined only by the…

The design and control of soft robots operating in fluid environments requires a careful understanding of the interplay between large elastic body deformations and hydrodynamic forces. Here we show that this interplay leads to novel…

It is shown that a compound elastic structure, which displays a dynamic instability, may be designed as the union (or 'fusion') of two structures which are stable when separately analyzed. The compound elastic structure has two degrees of…

Rotating the clamped ends of a buckled elastica induces a snap-through instability. Predicting the limit point and determining the equilibria at the start and end of the snap are routine computations in the quasi-static setting. The…

The stability analysis of elastic rings subjected to various loading conditions is examined, focusing on stable and unstable configurations. The harmonic balance method is employed to investigate the stability range under different loading…

Soft robots are notoriously hard to control. This is partly due to the scarcity of models able to capture their complex continuum mechanics, resulting in a lack of control methodologies that take full advantage of body compliance. Currently…

The concept of 'deformable arm scale' (completely different from a traditional rigid arm balance) is theoretically introduced and experimentally validated. The idea is not intuitive, but is the result of nonlinear equilibrium kinematics of…

Mechanical instabilities can be exploited to design innovative structures, able to change their shape in the presence of external stimuli. In this work, we derive a mathematical model of an elastic beam subjected to an axial force and…

A highly deformable rod, modelled as the extensible elastica, is connected to a movable clamp at one end and to a pin sliding along a frictionless curved profile at the other. Bifurcation analysis shows that axial compliance provides a…

Bifurcation of an elastic structure crucially depends on the curvature of the constraints against which the ends of the structure are prescribed to move, an effect which deserves more attention than it has received so far. In fact, we show…

Slender elastic objects such as a column tend to buckle under loads. While static buckling is well understood as a bifurcation problem, the evolution of shapes during dynamic buckling is much harder to study. Elastic rings under normal…

Many elastic structures exhibit rapid shape transitions between two possible equilibrium states: umbrellas become inverted in strong wind and hopper popper toys jump when turned inside-out. This snap-through is a general motif for the…

This work studies the dynamics of a one dimensional elastic bar with random elastic modulus and prescribed boundary conditions, say, fixed at one end, and attached to a lumped mass and two springs (one linear and another nonlinear) on the…

For soft robots to work effectively in human-centered environments, they need to be able to estimate their state and external interactions based on (proprioceptive) sensors. Estimating disturbances allows a soft robot to perform desirable…

Model-based manipulation of deformable objects has traditionally dealt with objects while neglecting their dynamics, thus mostly focusing on very lightweight objects at steady state. At the same time, soft robotic research has made…

Soft robots have high adaptability and safeness which are derived from their softness, and therefore it is paid attention to use them in human society. However, the controllability of soft robots is not enough to perform dexterous behaviors…

We investigate the morphology and mechanics of a naturally curved elastic arch loaded at its center and frictionally supported at both ends on a flat, rigid substrate. Through systematic numerical simulations, we classify the observed…

Experimental analysis of the mechanics of a deformable object, and particularly its stability, requires repetitive testing and, depending on the complexity of the object's shape, a testing setup that can manipulate many degrees of freedom…

We study elastic snap-through induced by a control parameter that evolves dynamically. In particular, we study an elastic arch subject to an end-shortening that evolves linearly with time, i.e. at a constant rate. For large end-shortening…