相关论文: Topological design of an asymmetric 3-translationa…
According to the topological design theory and method of parallel mechanism (PM) based on position and orientation characteristic (POC) equations, this paper design a novel 3-translation (3T) PM that has three advantages, i.e., 1) it…
This paper presents a novel three-degree-of-freedom (3-DOF) translational parallel manipulator (TPM) by using a topological design method of parallel mechanism (PM) based on position and orientation characteristic (POC) equations. The…
According to the topological design theory and method of parallel mechanism (PM) based on position and orientation characteristic (POC) equations, this paper studied a 3-DOF translational PM that has three advantages, i.e., (i) it consists…
This article presents a new three-degree-of-freedom (3-DOF) parallel mechanism (PM) with two translations and one rotation (2T1R), designed based on the topological design theory of the parallel mechanism using position and orientation…
Presented in this paper is the kinematic analysis of a symmetrical three-degree-of-freedom planar parallel manipulator. In opposite to serial manipulators, parallel manipulators can admit not only multiple inverse kinematic solutions, but…
The aim of this paper is the kinematic study of a 3-RPR planar parallel manipulator where the three fixed revolute joints are actuated. The direct and inverse kinematic problem as well as the singular configuration is characterized. On…
A class of analytic planar 3-RPR manipulators is analyzed in this paper. These manipulators have congruent base and moving platforms and the moving platform is rotated of 180 deg about an axis in the plane. The forward kinematics is reduced…
Flow-matching methods for 3D shape assembly learn point-wise velocity fields that transport parts toward assembled configurations, yet they receive no explicit guidance about which cross-part interactions should drive the motion. We…
A family of reconfigurable parallel robots can change motion modes by passing through constraint singularities by locking and releasing some passive joints of the robot. This paper is about the kinematics, the workspace and singularity…
Redundant parallel robots are normally employed in scenarios requiring good precision, high load capability, and large workspace compared to traditional parallel mechanisms. However, the elementary robotic configuration and geometric…
The determination of the mobility of parallel mechanisms (PM) is a fundamental problem. An automatic and intelligent analysis platform will be a significant tool for the design and optimization of mechanical systems. Based on the theory of…
In the modern days, manipulators are found in the automated assembly lines of industries that produce products in masses. These manipulators can be used only in one configuration, that is either serial or parallel. In this paper, a new…
Recursive modelling for the kinematics of a 3-PRP planar parallel robot is presented in this paper. Three planar chains connecting to the moving platform of the manipulator are located in a vertical plane. Knowing the motion of the…
This paper proposes a classification of three-revolute orthogonal manipulators that have at least one of their DH parameters equal to zero. This classification is based on the topology of their workspace. The workspace is characterized in a…
This paper focuses on the kinematic properties of a new three-degree-of-freedom hybrid manipulator. This manipulator is obtained by adding in series to a five-bar planar mechanism (similar to the one studied by Bajpai and Roth) a third…
This paper analyses the workspace of the three-revolute orthogonal manipulators that have at least one of their DH parameters equal to zero. These manipulators are classified into different groups with similar kinematic properties. The…
This paper studies the kinematic geometry of general 3-RPR planar parallel robots with actuated base joints. These robots, while largely overlooked, have simple direct kinematics and large singularity-free workspace. Furthermore, their…
This paper investigates singular configurations of planar 3-RPR parallel manipulators, which result from applying the averaging technique to solution pairs of their direct kinematic problem. Without computing the zeros of the corresponding…
Although parallel manipulators (PMs) started with the introduction of architectures with 6 Degrees of Freedom (DoF), a vast number of applications require less than 6 DoF. Consequently, scholars have proposed architectures with 3 DoF and 4…
The subject of this paper is the design of a new concept of modular parallel mechanisms for three, four or five-axis machining applications. Most parallel mechanisms are designed for three- or six-axis machining applications. In the last…