相关论文: Nanogaps by direct lithography for high-resolution…

Transmission electron beams (TEBs) have long been used to study and manipulate materials at nanometer scales. In the late 1970's, Cherns demonstrated surface pitting in Au films upon exposure to a 1MeV TEB and observed crystal dislocations…

For nanoscale electrical characterization and device fabrication it is often desirable to fabricate planar metal electrodes separated by large aspect ratio gaps with interelectrode distances well below 100 nm. We demonstrate a self-aligned…

Nanostructures have become an attractive subject due to many applications, particularly the photonic bandgap effect observed in photonic crystals. Nevertheless, the fabrication of such structures remains a challenge because of accurate…

Nano-size objects like metal clusters present an ideal system for the study of quantum phenomena and for constructing practical quantum devices. Integrating these small objects in a macroscopic circuit is, however, a difficult task. So far…

We developed a process to fabricate nanoscale metallic gate electrodes on scanning probe cantilevers, including on the irregular surface of protruding cantilever tips. The process includes a floating-layer technique to coat the cantilevers…

Electron microscopes have been improved to achieve ever smaller beam spots, a key parameter that determines the instrument's resolution. The techniques to measure the size of the beam, however, have not progressed to the same degree. There…

Transmission electron microscopy (TEM) is a powerful imaging tool that has found broad application in materials science, nanoscience and biology(1-3). With the introduction of aberration-corrected electron lenses, both the spatial…

The reduced dimensionality in two-dimensional materials leads a wealth of unusual properties, which are currently explored for both fundamental and applied sciences. In order to study the crystal structure, edge states, the formation of…

We have developed a controlled and highly reproducible method of making nanometer-spaced electrodes using electromigration in ambient lab conditions. This advance will make feasible single molecule measurements of macromolecules with…

We present results of a planar process development based on the combination of electron-beam lithography and dry etching for fabricating high-quality superconducting photosensitive structures in the sub-100nm regime. The devices were…

The fabrication of metallic single-walled carbon nanotube electrodes separated by gaps of typically 20nm width by electron-beam-induced oxidation is studied within an active device configuration. The tube conductance is measured…

Transmission electron microscopy at very low energy is a promising way to avoid damaging delicate biological samples with the incident electrons, a known problem in conventional transmission electron microscopy. For imaging in the 0-30 eV…

We have fabricated pairs of platinum electrodes with separation between 20 and 3.5 nm. Our technique combines electron beam lithography and chemical electrodeposition. We show that the measurement of the conductance between the two…

We have combined direct nanofabrication by local anodic oxidation with conventional electron-beam lithography to produce a parallel double quantum dot based on a GaAs/AlGaAs heterostructure. The combination of both nanolithography methods…

Near-field optical microscopy can be used as a viable route to understand the nanoscale material properties below the diffraction limit. On the other hand, atomically thin two-dimensional (2D) transition metal dichalcogenides (TMDs) are the…

This paper reports on a novel compact, low-loss bending technique for additively manufactured dielectric image lines between 140 GHz and 220 GHz. Conventional bending approaches require either large curvature radii or technologically…

Nanofabrication research pursues the miniaturization of patterned feature size. In the current state of the art, micron scale areas can be patterned with features down to ~ 30 nm pitch using electron beam lithography. Our work demonstrates…

A simple and highly reproducible technique is demonstrated for the fabrication of metallic electrodes with nanometer separation. Commercially available bare gold colloidal nanoparticles are first trapped between prefabricated…

Beam shaping - the ability to engineer the phase and the amplitude of massive and massless particles - has long interested scientists working on communication, imaging and the foundations of quantum mechanics. In light optics, the shaping…

Atomic resolution imaging in transmission electron microscopy (TEM) and scanning TEM (STEM) of light elements in electron-transparent materials has long been a challenge. Biomolecular materials, for example, are rapidly altered when…