相关论文: High strain rate compression of epoxy micro pillar…
Strain and defects in crystalline materials are responsible for the distinct mechanical, electric and magnetic properties of a desired material, making their study an essential task in material characterization, fabrication and design.…
Micropillar compression experiments probing size effects in confined plasticity of metal thin films, including the indirect imposition of 'canonical' simple shearing boundary conditions, show dramatically different responses in compression…
Previous studies have shown that the elastic properties of Zinc Dialkyl-dithiophosphate (ZDTP) tribofilms measured by nanoindentation increase versus applied pressure (Anvil effect) [1, 2]. The aim of this paper is to demonstrate that, up…
Electrically conducting polymers with mechanical adaptability are essential for flexible electronics, yet most suffer structural degradation under rapid deformation. In this study, multiscale coarse-grained (MSCG) simulations are used to…
A clear understanding of the dynamic behavior of metals is critical for developing superior structural materials as well as for improving material processing techniques such as cold spray and shot peening. Using a high velocity (from 120…
Metals exhibit an upturn in strength at strain rates of approximately 1000 s-1 - 3000 s-1, governed by rapid dislocation multiplication, interactions and storage. This phenomenon is strongly influenced by the initial dislocation density…
Hyper-viscoelastic polymers have multiple areas of application including aerospace, biomedicine, and automotive. Their mechanical responses are therefore extremely important to understand, particularly because they exhibit strong rate and…
An indentation testing method, which utilizes lateral contact of a long cylindrical indenter, is developed for a thin transversely isotropic incompressible elastic film deposited onto a smooth rigid substrate. It is assumed that the…
Voltage-induced magnetic anisotropy has been quantitatively studied in polycrystalline Ni thin film deposited on flexible substrate using microstrip ferromagnetic resonance. This anisotropy is induced by a piezoelectric actuator on which…
Conventional drop-weight techniques were modified to accommodate low-amplitude force transducer signals from low-strength, cold isostatically pressed 'heavy' composites of polytetrafluoroethylene, aluminum and tungsten. The failure…
The paper concerns the nanopowder high-speed, $10^4$ - $10^9$ s${}^{-1}$, compaction processes modeling by a two-dimensional granular dynamics method. Nanoparticles interaction, in addition to known contact laws, included dispersive…
Synchrotron Laue microdiffraction and Digital Image Correlation measurements were coupled to track the elastic strain field (or stress field) and the total strain field near a general grain boundary in a bent bicrystal. A 316L stainless…
Properties of typical MEMS materials have been widely investigated. Mechanical properties of MEMS structures depend not only on the bulk material properties, but also structural factors. A measurement system has been made to measure…
Static and dynamic analysis of the fracture tests of fiber composites in hydraulically servo-controlled testing machines currently in use shows that their grips are much too soft and light for observing the postpeak softening. Based on…
Nanoscale strain mapping by four-dimensional scanning transmission electron microscopy (4D-STEM) relies on determining the precise locations of Bragg-scattered electrons in a sequence of diffraction patterns, a task which is complicated by…
We study the physical properties of MnAs under strain by using accurate first-principles pseudopotential calculations. Our results provide new insight on the physics of strained multilayer that are grown epitaxially on different lattice…
We propose a spintronic strain sensor capable of sensing strain with a sensitivity of 1E-13/sqrt{Hz} at room temperature with an active sensing area of 1 cmE2 and power dissipation of 1 watt. This device measures strain by monitoring the…
Recently, the strain engineering of two-dimensional materials such as graphene has attracted considerable attention for its great potential in functional nanodevices. Here, we theoretically and experimentally investigate the strain…
Response to uniaxial stress has become a major probe of electronic materials. Tuneable uniaxial stress may be applied using piezoelectric actuators, and so far two methods have been developed to couple samples to actuators. In one,…
Recent progress in nanotechnology enables us to utilize the elastic strain engineering, the emerging technology capable of controlling the physio-chemical properties of materials via externally-imposed elastic strains, for hard materials.…