相关论文: A semi-analytical model for the wrinkling of lamin…

Thin elastic sheets bend easily, leading to mechanical instabilities such as wrinkling. Here, we investigate wrinkles at edges of bi-strips, which consist of two thin sheets, one that swells and one that does not, joined side-by-side. It is…

Surface wrinkling is an instability mode that is often observed in a wide variety of multilayer tubes under bending deformation. When the degree of applied bending exceeds a critical value, wrinkles appear at the intrados of the tube and…

The formation of periodic wrinkles in soft layered materials due to mechanical instabilities is prevalent in nature and has been proposed for use in multiple applications. However, such phenomena have been explored predominantly in…

Periodic wrinkling of a rigid capping layer on a deformable substrate provides a useful method for templating surface topography for a variety of novel applications. Many experiments have studied wrinkle formation during the compression of…

We investigate the buckling and post-buckling properties of a hyperelastic half-space coated by two hyperelastic layers when the composite structure is subjected to a uniaxial compression. In the case of a half-space coated with a {\it…

The method of molecular dynamics and molecular mechanics has been used to numerically simulate the formation of wrinkle systems during compression of a graphene sheet lying on a flat solid substrate. It is shown that under uniaxial…

Wrinkling is the phenomenon of out-of-plane deformation patterns in thin walled structures, as a result of a local compressive (internal) loads in combination with a large membrane stiffness and a small but non-zero bending stiffness.…

Complex textured surfaces occur in nature and industry, from fingerprints to lithography-based micropatterns. Wrinkling by confinement to an incompatible substrate is an attractive way of generating reconfigurable patterned topographies,…

The buckling of elastic bodies is a common phenomenon in the mechanics of solids. Wrinkling of membranes can often be interpreted as buckling under constraints that prohibit large amplitude deformation. We present a combination of analytic…

We study the dynamic coarsening of wrinkles in an elastic sheet that is compressed while lying on a thin layer of viscous liquid. When the ends of the sheet are instantaneously brought together by a small distance, viscous resistance…

Single-mode deformations of two-dimensional materials, such as the Miura-ori zig-zag fold, are important to the design of deployable structures because of their robustness; these usually require careful pre-patterning of the material. Here…

A paradigm for the study of wrinkling in elastic sheet is the Lam\'{e} configuration, in which azimuthal wrinkles form in an annular sheet subjected to tensile loads at both edges. Since wrinkles are spatially extended, this instability…

We prove theoretically that when a soft solid is subjected to an extreme deformation, wrinkles can form on its surface at an angle that is oblique to a principal direction of stretch. These oblique wrinkles occur for a strain that is…

Thin sheets that are forced at their boundaries develop a variety of shapes aimed at minimising elastic energy by curving spontaneously in ways that break the symmetry of the sheet and the forcing. Characterising such buckling generally…

A thin flat rectangular plate supported on its edges and subjected to in-plane loading exhibits stable post-buckling behaviour. However, the introduction of a nonlinear (softening) elastic foundation may cause the response to become…

We consider a disk-shaped thin elastic sheet bonded to a compliant sphere. (Our sheet can slip along the sphere; the bonding controls only its normal displacement.) If the bonding is stiff (but not too stiff), the geometry of the sphere…

Shells, when confined, can deform in a broad assortment of shapes and patterns, often quite dissimilar to what is produced by their flat counterparts (plates). In this work we discuss the morphological landscape of shells deposited on a…

We examine the buckling shape and critical compression of confined inhomogeneous composite sheets lying on a liquid foundation. The buckling modes are controlled by the bending stiffness of the sheet, the density of the substrate, and the…

Modeling of wrinkles and folds formation in single and multilayer graphene sheets lying on flat deformable (polymer) substrates has been carried out. It is shown that the deformability of the substrate leads to the appearance of significant…

Recent experiments by Kantsler et. al. (2007) have shown that the relaxational dynamics of a vesicle in external elongation flow is accompanied by the formation of wrinkles on a membrane. Motivated by these experiments we present a theory…