相关论文: Strain rate sensitivity of a Cu/Al$_2$O$_3$ multi-…
Microscale dynamic testing is vital to the understanding of material behavior at application relevant strain rates. However, despite two decades of intense micromechanics research, the testing of microscale metals has been largely limited…
Heterostructures consisting of PbZr0.2Ti0.8O3 and PbZr0.4Ti0.6O3 films grown on a SrTiO3 (100) substrate with a SrRuO3 bottom electrode were prepared by pulsed laser deposition. Using the additional interface provided by the ferroelectric…
Aluminosilicate (Al-Si-O) thin films containing up to 31 at. % Al and 23 at. % Si were prepared by reactive RF magnetron co-sputtering. Mechanical and structural properties were measured by indentation and specular reflectance infrared…
Al2O3 thin films have been deposited at substrate temperatures between 500{\deg}C to 600{\deg}C by reactive magnetron sputtering using an additional arbitrary substrate bias to tailor the energy distribution of the incident ions. The films…
An equimolar NiCoFeCrGa high entropy alloy having dual-phase homogeneous components was studied, where the constituent phases exhibit distinct mechanical properties. Micropillars with various diameters were created from two differently heat…
The deformation behavior of single crystal and nanocrystalline nickel were studied using in situ micropillar compression experiments from quasi-static to high strain rates up to 10^3 s-1. Deformation occurred by dislocation slip activity in…
Ultrafine-grained aluminum alloys offer interesting multifunctional properties with a combination of high strength, low electrical resistivity, and low density. However, due to thermally induced grain coarsening, they typically suffer from…
The microstructure and mechanical properties of materials saturate to steady states after severe plastic deformation (SPD). Despite the well-known effect of temperature on the steady-state microstructure, there is no general agreement on…
Magnetic multilayers of $(SrRuO_3)_m(SrMnO_3)_n$ were grown artificially using the pulsed laser deposition technique on (001)-oriented $SrTiO_3$ substrates. The state of strain at the interfaces and the structural coherency are studied in…
Controlling the microstructure of thin films is of critical importance for various applications. We demonstrate a methodology for tuning the local microstructure through film-substrate interactions using Ag-Cu as a model system. Metastable…
In order to get homogeneous nanostructured Aluminum Nitride deposits, thin films were grown at room temperature on [001] Si substrates by radio frequency magnetron reactive sputtering. The deposits were analysed by Transmission Electron…
Thin films of the charge-ordered (CO) compound Pr$_{0.5}$Ca$_{0.5}$MnO$_{3}$ have been deposited onto (100)-oriented SrTiO$_{3}$ substrates using the Pulsed Laser Deposition technique. Magnetization and transport properties are measured…
Understanding the mechanical properties of metals at extreme conditions is essential for the advancement of miniaturized technologies. As dimensions decrease, materials will experience higher strain rates at the same applied velocities.…
Advanced nanodevices require high-precision machining of thin films using ultrafast lasers. However, thin-film fabrications cause variations in microstructure, crystallographic orientation, and residual stresses owing to coating conditions…
$Al/AlO_x/Al$-layer systems are frequently used for Josephson junction-based superconducting devices. Although much work has been devoted to the optimization of the superconducting properties of these devices, systematic studies on…
Based on density functional theory (DFT) calculations including an on-site Hubbard $U$ term we investigate the effect of substrate-induced strain on the properties of ferrimagnetic Fe$_2$O$_3$-FeTiO$_3$ solid solutions and heterostructures.…
This work reports on sputter depositions carried out from a compound (Ti,Zr)2AlC target, whereupon Al-containing (Ti,Zr)C thin films (30-40 nm in thickness) were deposited on MgO(111) and Al2O3(0001) substrates at temperatures ranging…
Oblique angle deposited oxide thin films have opened up new dimensions in fabricating optical interference devices with tailored refractive index profile along thickness by tuning its microstructure by varying angle of deposition.…
The structure and microstrucutre of fully-strained BiCrO3 thin films have been investigated by X-rays diffraction and transmission electron microscopy, at room temperature. Interestingly, three structural variants are simultaneously…
Ferroelectric BaTiO3 films with large polarization have been integrated with Si(001) by pulsed laser deposition. High quality c-oriented epitaxial films are obtained in a substrate temperature range of about 300 deg C wide. The deposition…