相关论文: InGaN Metal-IN Solar Cell: optimized efficiency an…
Single junction Si solar cells dominate photovoltaics but are close to their efficiency limits. This paper presents ideal limiting efficiencies for tandem and triple junction multijunction solar cells subject only to the constraint of the…
Graphene has been intensively studied in photovoltaics focusing on emerging solar cells based on thin films, dye-sensitized, quantum dots, nanowires, etc. However, the typical efficiency of these solar cells incorporating graphene are below…
Multijunction solar cells are usually grown on Ge substrates. This implies several disadvantages that hinder the performance of the whole multijunction and limit their possible applications. The drawbacks caused by the substrate are:…
The efficiency of GaAs nanowire solar cells can be significantly improved without any new processing steps or material requirements. We report coupled optoelectronic simulations of a GaAs nanowire (NW) solar cell with vertical p-i-n…
Effect of geometrical and structural parameters on the efficiency of the tandem solar cell based on the III-V nanowire array on silicon is studied by the means of coupled opto-electrical simulations. A close to realistic structure,…
Multijunction solar cell design is guided by both the theoretical optimal bandgap combination as well as the realistic limitations to materials with these bandgaps. For instance, triple-junction III-V multijunction solar cells commonly use…
Compared to traditional pn-junction photovoltaics, hot carrier solar cells offer potentially higher efficiency by extracting work from the kinetic energy of photogenerated "hot carriers" before they cool to the lattice temperature. Hot…
The thermodynamic limit of photovoltaic efficiency for a single-junction solar cell can be readily predicted using the bandgap of the active light absorbing material. Such an approach overlooks the energy loss due to non-radiative…
Organic solar cells have reached record efficiencies with non-fullerene acceptors, yet their translation to industrial printing remains a critical bottleneck. Here we report the highest efficiency achieved for a fully…
Nano-scaled metallic or dielectric structures may provide various ways to trap light into thin-film solar cells for improving the conversion efficiency. In most schemes, the textured active layers are involved into light trapping structures…
ZnO/GaN alloys exhibit exceptional photocatalyst applications owing to the flexibly tunable band gaps that cover a wide range of the solar spectrum, and thus have attracted extensive attentions over the past few years. In this study,…
Ultra-wide bandgap (UWBG) materials hold immense potential for high-power RF electronics and deep ultraviolet photonics. Among these, AlGaN emerges as a promising candidate, offering a tunable bandgap from 3.4 eV (GaN) to 6.1 eV (AlN) and…
Traditional CdS buffer layer in selenium-free Cu(In,Ga)S2 solar cells leads to reduced open-circuit voltage because of a negative conduction band offset at the Cu(In,Ga)S2/CdS interface. Reducing this loss necessitates the substitution of…
Nanostructures, especially of silicon, are of paramount importance for new generation solar cell applications. The key material requirements for solar cells are good electrical conductivity, confinement of excitons, and a tunable band-gap…
III-V semiconductor-based photoelectrochemical (PEC) devices show the highest solar-to-electricity or solar-to-fuel conversion efficiencies. GaInP is a relevant top photoabsorber layer or a charge-selective contact in PEC for integrated and…
In this paper, we have designed and investigated the performance of radial GaAs/AlGaAs pin junction nanocone array solar cells by performing coupled optoelectronic simulations to obtain the most optimal design configuration based on its…
Scandium-doped aluminum nitride has recently emerged as a promising material for quantum photonic integrated circuits (PICs) due to its unique combination of strong second-order nonlinearity, ferroelectricity, piezoelectricity, and…
We investigate the optomechanical properties of tensile-strained ternary InGaP nanomembranes grown on GaAs. This material system combines the benefits of highly strained membranes based on stoichiometric silicon nitride, with the unique…
In$_2$Se$_3$ in the three-dimensional (3D) hexagonal crystal structure with space group $P6_1$ ($\gamma$-In$_2$Se$_3$) has a direct band gap of $\sim$1.8 eV and high absorption coefficient, making it a promising semiconductor material for…
Scandium aluminum nitride (ScAlN) has recently emerged as an attractive material for integrated photonics due to its favorable nonlinear optical properties and compatibility with CMOS fabrication. Despite the promising and versatile…