相关论文: Mapping the initiation of plastic deformation in n…
Nanoindentation, a common technique for probing the mechanical properties of crystalline materials, exhibits both surface and bulk-dominated responses that are linked to the parent crystal's elasticity and plasticity. For FCC crystals, the…
We present a comprehensive review of the physical behavior of yield stress materials in soft condensed matter, which encompass a broad range of materials from colloidal assemblies and gels to emulsions and non-Brownian suspensions. All…
When a suspension freezes, a compacted particle layer builds up at the solidification front with noticeable implications on the freezing process. In a directional solidification experiment of monodispersed suspensions in thin samples, we…
A promising approach to deform metallic-intermetallic composite materials is the application of electric current pulses during the deformation process to achieve a lower yield strength and enhanced elongation to fracture. This is known as…
Deformation plasticity mechanisms in alloys and compounds may unveil the material capacity towards optimal mechanical properties. We conduct a series of molecular dynamics (MD) simulations to investigate plasticity mechanisms due to…
We introduce new models that incorporate layer corrugation and interface roughness into standard approaches for measuring interface stress in nanomultilayers (NMLs). Applied to Cu/W NMLs, these models show that ignoring such features can…
A thin, elastic sheet floating on the surface of a liquid bath wrinkles when poked at its centre. We study the onset of wrinkling as well as the evolution of the pattern as indentation progresses far beyond the wrinkling threshold. We use…
We measure the local yield stress, at the scale of small atomic regions, in a deeply quenched two-dimensional glass model undergoing shear banding in response to athermal quasistatic (AQS) deformation. We find that the occurrence of…
Thin elastic two-dimensionnal systems under compressive stresses may relieve part of their stretching energy by developing out of plane undulations. We investigate experimentally and theoretically the indentation of an elastic disk…
This paper investigates the effects of plasticity on the effective fracture toughness. A layered material is considered as a modelling system. An elastic-plastic phase-field model and a surfing boundary condition are used to study how the…
Tungsten is the main candidate material for plasma-facing armour components in future fusion reactors. In-service, fusion neutron irradiation creates lattice defects through collision cascades. Helium, injected from plasma, aggravates…
Using molecular dynamics simulation, we study the plastic zone created during nanoindentation of a large CuZr glass system. The plastic zone consists of a core region, in which virtually every atom undergoes plastic rearrangement, and a…
The investigation of the deformation behaviour of intermetallic phases is mostly limited to high temperatures due to their low ductility at ambient temperature. Therefore, within this study, nanoindentation experiments on the Al$_{2}$Cu…
Indentation is a common experimental technique to study the mechanics of polymeric materials. The main advantage of using indentation is because this provides a direct correlation between the microstructure and the small-scale mechanical…
Micro-indentation test with a micro flat-end cone indenter was employed to simulate micro embossing process and investigate the thermo-mechanical response of ceramic green substrates. The laminated low temperature co-fired ceramic green…
Nanoindentation-induced phase transformation in silicon has been studied. A series of nanoindentations were made with the sharp diamond Berkovich tip. During nanoindentations, maximum load ranged from 2000 $\mu$N to 5000 $\mu$N, with a 1000…
We report the interplay between In incorporation and strain relaxation kinetics in high-In-content InxGa1-xN (x = 0.3) layers grown by plasma-assisted molecular-beam epitaxy. For In mole fractions x = 0.13-0.48, best structural and…
Surface tension is a prominent factor for the deformation of solids at micro-/nano-scale. This paper investigates the effects of surface tension on the two-dimensional contact problems of an elastic layer bonded to the rigid substrate.…
The stress transfer mechanism from a polymer substrate to a nano-inclusion, such as a graphene flake, is of extreme interest for the production of effective nanocomposites. Previous work conducted mainly at the micron scale has shown that…
When stressed sufficiently, solid materials yield and deform plastically via reorganization of microscopic constituents. Indeed, it is possible to alter the micro-structure of materials by judicious application of stress, an empirical pro-…