相关论文: Development and geometry of isotropic and directio…

We study the appearance and evolution of an array of parallel cracks in a thin slab of material that is directionally dried, and show that the cracks penetrate the material uniformly if the drying front is sufficiently sharp. We also show…

Volume alteration in solid materials is a common cause of material failure. Here we investigate the crack formation in thin elastic layers attached to a substrate. We show that small variations in the volume contraction and substrate…

We study a theoretical model of mud cracks, that is, the fracture patterns resulting from the contraction with drying in a thin layer of a mixture of granules and water. In this model, we consider the slip on the bottom of this layer and…

We investigate the formation of spiral crack patterns during the desiccation of thin layers of precipitates in contact with a substrate. This symmetry-breaking fracturing mode is found to arise naturally not from torsion forces, but from a…

Superficial (two dimensional) crack patterns appear when a thin layer of material elastically attached to a substrate contracts. We study numerically the maturation process undergone by these crack patterns when they are allowed to adapt in…

Cracks in thin layers are influenced by what lies beneath them. From buried craters to crocodile skin, crack patterns are found over an enormous range of length scales. Regardless of absolute size, their substrates can dramatically…

We investigate by means of computer simulations the effect of structural disorder on the statistics of cracking for a thin layer of material under uniform and isotropic drying. The layer is discretized into a triangular lattice of springs.…

Many clays, soils, biological tissues, foods, and coatings are shrinkable, granular materials: they are composed of packed, hydrated grains that shrink when dried. In many cases, these packings crack during drying, critically hindering…

When cracks form in a thin contracting layer, they sequentially break the layer into smaller and smaller pieces. A rectilinear crack pattern encodes information about the order of crack formation, as later cracks tend to intersect with…

A fascinating class of patterns, often encountered in nature as meandering cracks on rocks, dried-out fields and tectonic plates is produced by the fracture of solids. Here we report the observation and modeling of an unusual type of…

We study pattern selection of cracks in directionally drying fractures by analyzing the experimental systems recently devised by C. Allain and L. Limat. [Phys. Rev. Lett. {\bf 74}, 2981 (1995).] Proposing a simple picture of crack…

While cracks in isotropic homogeneous materials propagate straight, perpendicularly to the tensile axis, cracks in natural and synthetic composites deflect from a straight path, often increasing the toughness of the material. Here we…

An asymptotic interface equation for directional solidification near the absolute stabiliy limit is extended by a nonlocal term describing a shear flow parallel to the interface. In the long-wave limit considered, the flow acts…

Cohesive granular materials, like wet sand, retain their shape before yielding under stress. This solid-like behavior is associated with elasticity. As the loading increases, the material typically flows. However, cohesive materials can…

We investigate the geometry of two-dimensional polygonal cracking that forms on the air-exposed surface of dried starch slurries. Two different kinds of starches, made from potato and corn, exhibited distinguished crack evolution, and there…

We experimentally study the formation of surface patterns in grafted hydrogel films of nanometer-to-micrometer thicknesses during imbibition-driven swelling followed by evaporation-driven shrinking. Creases are known to form at the hydrogel…

Liquid droplets usually wet smooth and homogeneous substrates isotropically. Recent research works have revealed that droplets sit, slide and spread anisotropically on uniaxially stretched soft substrates, showing an enhanced wettability…

Polygonal desiccation crack patterns are commonly observed in natural systems. Despite their quotidian nature, it is unclear whether similar crack patterns which span orders of magnitude in length scales share the same underlying physics.…

Aqueous colloidal dispersions of silica particles become anisotropic when they are dried through evaporation. This anisotropy is generated by a uniaxial strain of the liquid dispersions as they are compressed by the flow of water toward a…

The fracture mechanics was widely employed to explain the crack propagation in the deposition produced by drying colloidal suspension. However, more complex than conventional fracture, those cracks periodically distribute and make up a…