相关论文: High-quality femtosecond laser surface micro/nano-…
Laser fragmentation of suspended microparticles is an upcoming alternative to laser ablation in liquid (LAL) that allows to streamline the the delivery process and optimize the irradiation conditions for best efficiency. Yet, the structural…
Precise control of surface properties including electrical characteristics, wettability, and friction is a prerequisite for manufacturing modern organic electronic devices. The successful combination of bottom up approaches for aligning and…
Ultra-fast femtosecond (fs) lasers provide a unique technological opportunity to precisely and efficiently micromachine materials with minimal thermal damage owing to the reduced heat transfer into the bulk of the work material offered by…
Ultrafast Bessel beams demonstrate a significant capacity of structuring transparent materials with high degree of accuracy and exceptional aspect ratio. The ability to localize energy on the nanometer scale (bypassing the 100 nm milestone)…
Semiconductor lasers with ultra-low thresholds and minimal footprints are a topic of active research. Such devices require a combination of high quality factor laser cavities with small active region volumes, which drives the quest for…
Nanostructuring hard optical crystals has so far been exclusively feasible at their surface, as stress induced crack formation and propagation has rendered high precision volume processes ineffective. We show that the inner chemical etching…
Fabrication of large area (sub 1 cm cross-section) micro-optical components in a short period of time (approximately 10 min) and with lesser number of processing steps is highly desirable and cost-effective. In the recent years, femtosecond…
Remarkable improvement in the removal efficiency of the ultraviolet laser (fourth harmonic wave of Nd:YAG laser) ablation was observed by irradiating a weak infrared laser (fundamental wave of Nd:YAG laser) simultaneously and additionally…
Fringe projection profilometry-based 3-D reconstruction of objects with high reflectivity and low surface roughness remains a significant challenge. When measuring such glossy surfaces, specular reflection and indirect illumination often…
The optical response of nickel is studied in a wide range of laser fluence, below and above the ablation threshold, by selfreflectivity measurements of ultrashort 800nm single laser pulses. At the ablation threshold, the reflectivity…
Nanosecond laser ablation of p-type Si(111) wafer is presented under an ambient, a water and a glycerin conditions. Effects of pulse energy, number of pulses and type of environment are systematically analyzed with an Optical Profilometer,…
This work reports on the fabrication of microbump structures on Ni films by single-pulse, localized laser irradiation. Conditions for the reproducible formation of such microstructures have been identified in terms of laser-irradiation and…
An intense femtosecond-laser excitation of a solid induces highly nonthermal conditions. In materials like silicon, laser-induced bond-softening leads to a highly incoherent ionic motion and eventually nonthermal melting. But is this…
Transparent biological tissues can be precisely dissected with ultrafast lasers using optical breakdown in the tight focal zone. Typically, tissues are cut by sequential application of pulses, each of which produces a single cavitation…
We use metal nanostructures (nanoplasmonics) excited with dual frequency lasers to generate and detect high frequency (> 10 GHz) sound wave resonances in water. The difference frequency between the two lasers causes beating in the…
We report on the studies of switching mechanism between normal and anomalous laser induced periodic surface structures. We have shown that for high loss metals the switching mechanism between normal and anomalous modes relays on an…
The effects of turbulence intensity and turbulence region on the distribution of femtosecond laser filaments are experimentally elaborated. Through the ultrasonic signals emitted by the filaments, and it is observed that increasing…
Femtosecond pulsed lasers have been widely used over the past decades for precise materials structuring at the micro- and nano- scales. In order, though, to realize efficient material processing and account for the formation of laser…
We investigated laser-induced periodic surface structures (LIPSS) generated on indium-tin-oxide (ITO) thin films with femtosecond laser pulses in the infrared region. Using pulses between 1.6 and 2.4 ${\mu}$m central wavelength, we observed…
The emergence of planar meta-lenses on flexible materials has profoundly impacted the long-standing perception of diffractive optics. Despite their advantages, these lenses still face challenges in design and fabrication to obtain high…