相关论文: Anti-microbial properties of a multi-component all…
Metallic glasses are excellent candidates for biomedical implant applications due to their inherent strength and corrosion resistance. Use of metallic glasses in structural applications is limited, however, because bulk dimensions are…
The electrical resistivity and the anisotropic magnetoresistance (AMR) was investigated for Ni Co alloys at and below room temperature. The Ni Co alloy layers having a thickness of about 2 um were prepared by electrodeposition on Si wafers…
Predicting the mechanical failure of parts in service requires understanding their deformation behavior, and associated dynamic microstructural evolution up to the near-atomic scale. Solutes are known to interact with defects generated by…
Predicting the structural response of advanced multiphase alloys and understanding the underlying microscopic mechanisms that are responsible for it are two critically important roles modeling plays in alloy development. An alloys…
Silicon anodes offer high energy densities for next-generation lithium-ion batteries; however, their application is limited by severe volume expansion during cycling. Making silicon porous or nanostructured mitigates this expansion but…
Next generation batteries based on lithium (Li) metal anodes have been plagued by the dendritic electrodeposition of Li metal on the anode during cycling, resulting in short circuit and capacity loss. Suppression of dendritic growth through…
Nanometric solid solution alloys are utilized in a broad range of fields, including catalysis, energy storage, medical application, and sensor technology. Unfortunately, the synthesis of these alloys becomes increasingly challenging as the…
Soft magnetic materials (SMMs) serve in electrical applications and sustainable energy supply, allowing magnetic flux variation in response to changes in applied magnetic field, at low energy loss1. The electrification of transport,…
Two-dimensional (2D) materials, such as transition metal dichalcogenides (TMDCs) in the 2H or 1T crystal phases, are promising (electro)catalyst candidates due to their high surface to volume ratio and composition of low-cost, abundant…
Neural prosthetics are typically situated in an aggressive, biochemical environment that requires materials with superior stability and performance. These probes have dual functionalities of recording and stimulation. The material stability…
Recycled aluminum alloys are pivotal for sustainable manufacturing, offering strength, durability, and environmental advantages. However, the presence of iron (Fe) impurities poses a major challenge, undermining their properties and…
The increasing resistance of Cu interconnects for decreasing dimensions is a major challenge in continued downscaling of integrated circuits beyond the 7-nm technology node as it leads to unacceptable signal delays and power consumption in…
This paper presents the findings of the synthesis of multicomponent (Al, W, Ni, Ti, Nb) alloy coatings from mosaic targets. For the study, a pulsed magnetron sputtering method was employed under different plasma generation conditions:…
Mechano-bactericidal (MB) surfaces have been proposed as an emerging strategy for preventing biofilm formation. Unlike antibiotics and metal ions that chemically interfere with cellular processes, MB nanostructures cause physical damage to…
The paper presents a new approach, based on controlled oxidation of nanoscale metallic multilayers, to produce strong and hard oxide/metal nanocomposite coatings with high strength and good thermal stability. The approach is demonstrated by…
Open-porous scaffolds of WE43 Mg alloy with a body-center cubic cell pattern were manufactured by laser powder bed fusion with different strut diameters. The geometry of the unit cells was adequately reproduced during additive manufacturing…
Thin-film nanocomposites, consisting of silver nanoparticles embedded in a dielectric Teflon\textregistered AF matrix, were synthesized using vapor phase co-deposition. The electrical conductivity of these composites was measured in-situ as…
A combination of high strength and reasonable ductility has been achieved in a copper-1.7 at.%titanium alloy deformed by high-pressure torsion. Grain refinement and a spinodal microstructure provided a hardness of 254 +/- 2 HV , yield…
Quaternary phases formed in copper alloys are investigated through a combination of quantum-mechanical and classical computer simulations and active machine learning. Focus is given on nickel, silicon, and chromium impurities in a copper…
Nanoparticle sintering remains a critical challenge in heterogeneous catalysis. In this work, we present a unified deep potential (DP) model for Cu nanoparticles on three Al$_2$O$_3$ surfaces ($\gamma$-Al$_2$O$_3$(100),…