相关论文: Evaluation of an Inflated Beam Model Applied to Ev…
A cylindrical elastomer tube can stay in an everted state without any applied external forces. If the thickness of the tube is small, the everted tube, except for the regions close to the two ends of the tube, is cylindrical, if the…
We derive a one-dimensional (1d) model for the analysis of bulging or necking in an inflated hyperelastic tube of {\it finite wall thickness} from the three-dimensional finite elasticity theory by applying the dimension reduction…
Mechanical instability in a pre-tensioned finite hyperelastic tube subjected to a slowly increasing internal pressure produces a spatially localized bulge at a critical pressure. The subsequent fate of the bulge, under continued inflation,…
Inflated-beam soft robots, such as tip-everting vine robots, can control curvature by contracting one beam side via pneumatic actuation. This work develops a general finite element modeling approach to characterize their bending. The model…
We evaluate the loss of stability of axially compressed slender and thick-walled tubes subject to a residual stress distribution. The nonlinear theory of elasticity, when used to analyze the underlying deformation, shows that the residual…
Motivated by applications to seed germination, we consider the transverse deflection that results from the axisymmetric indentation of an elastic membrane by a rigid body. The elastic membrane is fixed around its boundary, with or without…
We investigate with experiments the twist induced transverse buckling instabilities of an elastic sheet of length $L$, width $W$, and thickness $t$, that is clamped at two opposite ends while held under a tension $T$. Above a critical…
We discuss the response of thin cylindrical tubes to small indentations. The stretching-free embedding of these surfaces is completely determined by the embedding of one edge curve, thus reducing their bending response to an effectively one…
In this paper an experimental validation of numerical approaches aimed to predict the coupled behaviour of microbeams for out-of-plane bending tests is performed. This work completes a previous investigation concerning in plane microbeams…
The large deflections of cantilevered beams and plates are modeled and discussed. Traditional nonlinear elastic models (e.g., that of von Karman) employ elastic restoring forces based on the effect of stretching on bending, and these are…
We present a study on swelling-induced circumferential buckling of tubular shaped gels. Inhomogeneous stress develops as gel swells under mechanical constraints, which gives rise to spontaneous buckling instability without external force.…
When a pair of parallel buckling beams of unequal width make lateral contact under increasing compression, eventually either the thin or the thick beam will snap, leading to collective motion of the beam pair. Using experiments and FEM…
We employ a first principles, force-level approach to self-consistently construct the anharmonic tube confinement field for entangled fluids of rigid needles and for primitive-path (PP) level chains in two limiting situations where chain…
We uncover how nonlinearities dramatically alter the buckling of elastic beams. First, we show experimentally that sufficiently wide ordinary elastic beams and specifically designed metabeams ---beams made from a mechanical metamaterial---…
A dielectric elastomer whose edges are held fixed will buckle, given sufficient applied voltage, resulting in a nontrivial out-of-plane deformation. We study this situation numerically using a nonlinear elastic model which decouples two of…
We investigate the mechanics of bistable, hard-magnetic, elastic beams, combining experiments, finite element modeling (FEM), and a reduced-order theory. The beam is made of a hard magneto-rheological elastomer, comprising two segments with…
Reducing wake losses in wind farms by deflecting the wakes through turbine yawing has been shown to be a feasible wind farm controls approach. Nonetheless, the effectiveness of yawing depends not only on the degree of wake deflection but…
In the context of the Damage Mechanics Challenge, we adopt a phase-field model of brittle fracture to blindly predict the behavior up to failure of a notched three-point-bending specimen loaded under mixed-mode conditions. The beam is…
The tube model is a central concept in polymer physics, and allows to reduce the complex many-filament problem of an entangled polymer solution to a single filament description. We investigate the probability distribution function of…
We consider a beam model representing the transverse deflections of a one dimensional elastic structure immersed in an axial fluid flow. The model includes a nonlinear elastic restoring force, with damping and non-conservative terms…