相关论文: Evolution of texture and microstructure during acc…
We studied the microstructural evolution of the low stacking fault energy $\alpha$-brass alloy CuZn15 during accumulative roll bonding (ARB). Most notably, the typical brass-type texture was clearly observed after four ARB passes (approx.…
Additively manufactured high strength aluminium alloy AA7075 was prepared using selective laser melting. High strength aluminium alloys prepared by selective laser melting have not been widely studied to date. The evolution of…
This work presents a pilot study on a strained complex concentrated alloy based on refractory elements: MoNbTaTiZr. Initially, the as-cast and homogenization-annealed conditions were characterized. After casting, the alloy consists of two…
Components manufactured via Wire + Arc Additive Manufacturing are usually characterised by large columnar grains. This can be mitigated by introducing in-process cold-rolling; in fact, the associated local plastic deformation leads to a…
Lightweight refractory high-entropy alloy coatings (RHEAcs) of NbxMo$_{0.5}$Ti$_{1.5}$Ta$_{0.2}$Cr (where $x=$ 1, 1.3, 1.5, and 2) were fabricated on the surface of 316L stainless steel using laser cladding (LC) technology. A comprehensive…
Microstructural features and mechanical properties of an Al-Mg-Si alloy processed by high-pressure torsion have been investigated using transmission electron microscopy, X-ray diffraction, three-dimensional atom probe, tensile tests and…
Accumulative Roll Bonding(ARB) process was used to develop few-layer graphene nano platelets reinforced aluminum matrix (GNPs/Al) composite in the form of sheets. Annealed Al sheets were ARB processed up to 6 pass along with coating of…
High-energy synchrotron x-rays are used to track grain rotations and the micromechanical evolution of a hexagonal Ti-7Al microstructure as it is cyclically loaded below its macroscopic yield stress. The evolution of the grains through 200…
This work demonstrates the development of a strong and ductile medium entropy alloy by employing conventional alloying and thermomechanical processing to induce partial recrystallization (PR) and precipitation strengthening in the…
Additively manufactured (AM) alloys have heterogeneous microstructures with broad grain size distributions and highly anisotropic and/or non-convex grain shapes. AM components can have complex geometries and porosity which may affect the…
The influence of the physical mechanisms activated during deformation and annealing on the microstructure and texture evolution as well as on the mechanical properties in the equiatomic CoCrFeMnNi high-entropy alloy (HEA) were investigated.…
A new method of combined loading was developed for manufacturing large - scale ingot of alpha-beta titanium alloy Ti-6Al-4V with the diameter of the gauge 120 mm and the length 300 mm. The process includes torsion with simultaneous tensile…
Despite the fast development of computational materials modelling, theoretical description of macroscopic elastic properties of textured polycrystalline aggregates starting from basic principles remains a challenging task. In this…
Ultrafine-grained aluminum alloys offer interesting multifunctional properties with a combination of high strength, low electrical resistivity, and low density. However, due to thermally induced grain coarsening, they typically suffer from…
The physical property characterization of Al doped Mg1-xAlxB2 system with x = 0.0 to 0.50 is reported. The results related to phase formation, structural transition, resistivity R(T) and magnetization M(T) measurements are discussed in…
An age-hardenable Al-Cu-Mg alloy (A2024) was processed by high-pressure torsion (HPT) for producing an ultrafine-grained structure. The alloy was further aged for extra strengthening. The tensile strength then reached a value as high as ~1…
Correlated analysis of (sub)grains and particles in alloys is important to understand transformation processes and control material properties. A multimodal data fusion workflow directly combining subgrain data from electron backscatter…
This study explores Ti-containing complex concentrated alloys (CCAs) within the AlMoNbTiZr system, focusing on compositions located in regions of the Bo-Md diagram characterized by low bond order (Bo) and d-orbital energy level (Md). Four…
Hot Isostatic Pressing was applied to synthesize bulk samples with diameter up to 30 mm starting with Alfa Aesar magnesium diboride powder. HIPing at 2 kbar, 1000 C with cooling under pressure (DMCUP cycle) resulted in a fully dense (or low…
One of the main material properties altered by rare earth additions in magnesium alloys is texture, which can be specifically adjusted to enhance ductility and formability. The current study aims at illuminating the texture selection…