相关论文: Surface analysis of tiles and samples exposed to t…

For the ITER-like wall, the JET mirror link divertor spectroscopy system was redesigned to fully cover the tungsten horizontal strike plate with faster time resolution and improved near-UV performance. Since the ITER-like wall project…

Analytical results of a complete JET cryopump regeneration, including the nitrogen panel, following the first ITER-Like Wall campaign are presented along with the in-situ analyses of residual gas. H/D mixtures and impurities such as…

The aim of the JET ITER-like Wall Project was to provide JET with the plasma facing material combination now selected for the DT phase of ITER (bulk beryllium main chamber limiters and a full tungsten divertor) and, in conjunction with the…

This paper investigates the effect of the ITER-like wall (ILW) on runaway electron (RE) generation through a comparative study of similar slow argon injection JET disruptions, performed with different wall materials. In the carbon wall…

The former all-carbon wall on JET has been replaced with beryllium in the main torus and tungsten in the divertor to mimic the surface materials envisaged for ITER. Comparisons are presented between Type I H-mode characteristics in each…

In this paper important aspects of Lower Hybrid (LH) operation with the ITER Like Wall (ILW) [1] at JET are reported. Impurity release during LH operation was investigated and it was found that there is no significant Be increase with LH…

We report on the detection by means of Raman spectroscopy of amorphous beryllium deuteride, BeD 2 , in magnetron sputtered deposits synthesized in two different laboratories and containing about 20 at.% of deuterium. In contrast, this…

The replacement of the JET carbon wall (C-wall) by a Be/W ITER-like wall (ILW) has affected the plasma energy confinement. To investigate this, experiments have been performed with both the C-wall and ILW to vary the heating power over a…

A complete global balance for carbon in JET requires knowledge of the net erosion in the main chamber, net deposition in the divertor and the amount of dust and flakes collecting in the divertor region. This paper describes a number of…

To avoid reflectivity losses in ITER optical diagnostic systems, plasma sputtering of metallic First Mirrors is foreseen in order to remove deposits coming from the main wall (mainly beryllium and tungsten). Therefore plasma cleaning has to…

This paper compares the gyrokinetic instabilities and transport in two representative JET pedestals, one (pulse 78697) from the JET configuration with a carbon wall (C) and another (pulse 92432) from after the installation of JET's…

This paper presents the DYON simulations of the plasma burn-through phase at Joint European Torus (JET) with the ITER-like wall. The main purpose of the study is to validate the simulations with the ITER-like wall, made of beryllium.…

To reduce the impact of charging effects on satellites, cheap and lightweight conductive coatings are desirable. We mimic space-like charging environments in ultra-high vacuum (UHV) chambers during deposition of charges via the electron…

Plasma Surface Interaction(PSI) effects on plasma burn-through are compared for the carbon wall and the ITER-Like Wall(ILW) at JET. For the carbon wall, the radiation barrier and C2+ influx have a significant linear correlation whereas the…

First mirrors will be the plasma facing components of optical diagnostic systems in ITER. Mirror surfaces will undergo modification caused by erosion and re-deposition processes [1,2]. As a consequence, the mirror performance may be changed…

From orbit, the visibility of Titan's surface is limited to a handful of narrow spectral windows in the near-infrared (near-IR), primarily from the absorption of methane gas. This has limited the ability to identify specific compounds on…

Project Daedalus (1973--1978), the most detailed interstellar probe design study ever conducted, specified a 9 mm beryllium erosion shield to protect the spacecraft payload during its 5.9 light-year cruise to Barnard's Star at 12% of the…

The major aspects linked to the use of the JET auxiliary heating systems: NBI, ICRF and LHCD, in the new JET ITER-like wall (JET-ILW) are presented. We show that although there were issues related to the operation of each system, efficient…

A laser ablation system has been constructed and used to determine the damage threshold of stainless steel, rhodium and single-, poly- and nanocrystalline molybdenum in vacuum, at a number of wavelengths between 220 and 1064 nm using 5 ns…

Achieving self-consistent performance predictions for ITER requires integrated modeling of core transport and divertor power exhaust under realistic impurity conditions. We present results from the first systematic power-flow and…