相关论文: Surface analysis of tiles and samples exposed to t…
We present a comprehensive account of the proton radiation hardness of Eljen Technology's EJ-500 optical cement used in the construction of experiment detectors. The cement was embedded into five plastic scintillator tiles which were each…
It is planned to use atomic processes to spread out most of the heating power over the first wall and side walls to reduce the heat loads on the plasma facing components in ITER to ~ 50 MW. Calculations indicate that there will be 100 MW in…
White light interferometry (WLI) can be used to obtain surface morphology information on dimensional scale of millimeters with lateral resolution as good as ~1 {\mu}m and depth resolution down to 1 nm. By performing true three-dimensional…
A high-strength dual alpha+beta phase titanium alloy Ti-6Al-4V is utilized as a material for beam windows in several accelerator target facilities. However, relatively little is known about how material properties of this alloy are affected…
The SPIDER experiment, part of the Neutral Beam Test Facility (NBTF) at Consorzio RFX (Padua, Italy), is the prototype of the negative ion source for the ITER neutral beam injectors; the source is coupled to a 100 kV three-grid acceleration…
It is well-known that extreme ultraviolet emission emitted at the solar surface is absorbed by overlying cool plasma. Especially in active regions dark lanes in EUV images suggest that much of the surface activity is obscured. Simultaneous…
The role of impurity radiation in the reduction of heat loads on divertor plates in present experiments such as DIII-D, JET, JT-60, ASDEX, and Alcator C-Mod, and in planned experiments such as ITER and TPX places a new degree of importance…
The flow patterns created by a coherent horizontal liquid jet impinging on a vertical wall atmoderate flow rates (jet flowrates 0.5-4.0 L min-1, jet velocities 2.6-21 m s-1) are studied withwater on glass, polypropylene and…
The power load to the divertor surfaces is a key concern for future devices such as ITER, due to the thermal limits on the material surface. One factor that characterizes the heat flux to the divertor is the fall off length in the…
This paper describes a new way to reconstruct and identify muons with high efficiency and high pion rejection. Since muons at the ILC are often produced with or in jets, for many of the physics channels of interest[1], an efficient…
Jet reconstruction in an ultra-relativistic heavy-ion collision suffers from a notoriously large, fluctuating thermal background. Traditional background subtraction methods struggle to remove this soft background while preserving the jet's…
The performance of the energy degrader in terms of beam properties directly impacts the design and cost of cyclotron-based proton therapy centers. The aim of this study is to evaluate the performances of different existing and novel…
The structure of six tiles extracted from the erosion and deposition zones (thin and thick deposition) of the Tore Supra toroidal pump limiter (TPL) have been analysed in the framework of the DITS campaign using micro-Raman spectroscopy.…
Impact collision ion scattering spectroscopy (ICISS), which is a variation of low energy ion scattering (LEIS) that employs large scattering angles, is performed on Bi2Se3 surfaces prepared by ion bombardment and annealing (IBA). ICISS…
The fast volumetric deposition of multi-MeV high current runaway electron (RE) beams constitutes the most critical issue for the ITER tungsten (W) first wall (FW) longevity. Such relativistic electron beams could generate extreme volumetric…
Background events in the DRIFT-IId dark matter detector, mimicking potential WIMP signals, are predominantly caused by alpha decays on the central cathode in which the alpha particle is completely or partially absorbed by the cathode…
Surface sensitive x-ray scattering techniques with atomic scale resolution are employed to investigate the microscopic structure of the surface of three classes of liquid binary alloys: (i) Surface segregation in partly miscible binary…
Predicting three-dimensional thermal loads during tokamak disruptions is essential for ITER yet remains weakly developed. We present a physics-based workflow that couples MHD simulations of vertical displacement events with field line…
The isovector reorientation (IVR) effect of deuteron scattering on heavy target provides a novel means to probe the nuclear isovector potential, which gives rise to the nuclear symmetry energy. The simulation studies on the experimental…
When using Ion Cyclotron Range of Frequency (ICRF) heating, enhanced heat-fluxes are commonly observed on some plasma facing components close to the antennas. Experiments have recently been carried out on JET with the new ITER-Like-Wall…