相关论文: Effect of Metal Element in Catalytic Growth of Car…
Feedstock and byproduct diffusion in the root growth of aligned CNT arrays was discussed in this work. A non-dimensional modulus was proposed to differentiate catalyst-decay controlled growth deceleration from diffusion controlled one. It…
Recent direct measurements of the growth kinetics of individual carbon nanotubes revealed abrupt changes in the growth rate of nanotubes maintaining the same crystal structure. These stochastic switches call into question the possibility of…
We report on the synthesis of carbon nanotubes on quasicrystalline alloys. Aligned multiwalled carbon nanotubes (MWNTs) on the conducting faces of decagonal quasicrystals were synthesized using floating catalyst chemical vapor deposition.…
The electronic breakdown and the bias dependence of the conductance have been investigated for a large number of catalytic chemical vapor deposition (CCVD) grown single-walled carbon nanotubes (SWCNTs) with very small diameters. The…
In most envisioned applications, full utilization of a graphene-carbon nanotube (CNT) construct requires maintaining the integrity of the graphene layer during the CNT growth step. In this work, we exhibit an approach towards controlled CNT…
Fe filled carbon nanotubes were synthesized by atmospheric pressure chemical vapor deposition using a simple mixture of iron acetylacetonate with a conventional photoresist and the effect of growth temperature from 550 to 950 {\deg}C on Fe…
A nanoscopic simulation for an acceleration sensor is aimed based on the piezoresistive effect of carbon nanotubes (CNTs). Therefore, a compact model is built from density functional theory (DFT), compared with results of molecular dynamics…
The methods of carbon nanotubes (CNTs) growth inside nanoporous materials are among the best candidates to fabricate CNTs with controlled geometrical parameters. We report obtaining CNTs by pyrolysis of sugar water and show that this…
Vertically-aligned carbon nanotube (CNT) "forest" microstructures fabricated by chemical vapor deposition (CVD) using patterned catalyst films typically have a low CNT density per unit area. As a result, CNT forests have poor bulk…
Because of their natural one-dimensional (1D) structure combined with intricate chiral variations, carbon nanotubes (CNTs) exhibit various exceptional physical properties, such as ultrahigh electrical and thermal conductivity, exceptional…
Corrosion is an inevitable phenomenon that is inherent in metals and even though there has been significant research on this subject, no ideal protection has been discovered to fully prevent corrosion. However, methods such as using…
In this work we use density functional theory (DFT) calculations to benchmark empirical potentials for the interaction between nickel and sp$^2$ bonded carbon nanoparticles. These potentials are then used in order to investigate how Ni…
Carbon nanotubes (CNTs) have found plenty of applications in electronics, sensing, actuation, mechanical structures, etc. There is a growing demand to produce large scale arrays of CNTs that can satisfy the requirements of cost effective,…
Although individual carbon nanotubes (CNTs) are superior as constituents to polymer chains, the mechanical and thermal properties of CNT fibers (CNTFs) remain inferior to commercial synthetic fibers due to the lack of synthesis methods to…
Through a careful modeling of interactions, collisions, and the catalytic behavior, one can obtain important information about the initial stage of growth of single-wall carbon nanotubes (SWCNTs), where a state-of-the-art semi-empirical…
Three different catalysts (Fe, Ni, Co nitrates dissolved in ethanol) were patterned on a SiO2/Si substrate and multi-wall carbon nanotubes were grown by catalytic decomposition of acetylene. We compare the growth of the carbon…
The rapid progress on MgB2 superconductor since its discovery[1] has made this material a strong competitor to low and high temperature superconductors (HTS) for applications with a great potential to catch the niche market such as in…
We prepared three ferrite nanocatalysts: (i) copper ferrite (CuFe2O4), (ii) ferrite where cobalt was substituted by nickel (NixCo1-xFe2O4, with x= 0, 0.2, 0.4, 0.6), and (iii) ferrite where nickel was substituted by zinc (ZnyNi1-yFe2O4 with…
We theoretically study the interplay between electrical and mechanical properties of suspended, doubly clamped carbon nanotubes in which charging effects dominate. In this geometry, the capacitance between the nanotube and the gate(s)…
We have studied photocurrent generation in large carbon nanotube (CNT) films using electrodes with different spacings. We observe that the photocurrent depends strongly on the position of illumination, with maximum observed response…