相关论文: A small sealed Ta crucible for thermal analysis of…
To obtain single crystals by solution growth, an exposed primary solidification surface in the appropriate, but often unknown, equilibrium alloy phase diagram is required. Furthermore, an appropriate crucible material is needed, necessary…
When diamond anvil cell (DAC) sample chambers are outfitted with both thermal insulation and electrodes, two cutting-edge experimental methods are enabled: Joule heating with spectroradiometric temperature measurement, and electrical…
Warm forming processes have been successfully applied at laboratory level to overcome some important drawbacks of the Al-Mg alloys, such as poor formability and large springback. However, the numerical simulation of these processes requires…
Simultaneous differential thermal analysis (DTA) and thermogravimetric (TG) measurements with copper oxide/aluminum oxide mixtures were performed in atmospheres with varying oxygen partial pressures and with crucibles made of different…
An instrument has been constructed to measure a large range of magnetostriction and thermal expansion between room temperature and 4 K in a superconductive split-coil magnet, that allows investigation in magnetic fields up to 12 T. The very…
A specific heat measuring instrument, with the capacity for the application of magnetic fields up to 9 Tesla, resorting to microcalorimetry chips from the company Xensor Integration, has been successfully assembled and its functioning…
Conductive ceramics played an important role in industries and manufactures due to their wide applications on electronics devices. Many synthesis approaches to prepare ceramics have been developing rapidly in the few decades. One of the…
Following the recent theoretical prediction of superconductivity in hole doped LiBC by Rosner et al [1], we have attempted to synthesise Li deficient LixBC (x = 1, 0.8, 0.6 and 0.4) and look for superconductivity in this system. Our…
We describe how we can precisely measure variations in the entropy S of small solid samples below room temperature, as a function the temperature T or the external magnetic field H, respectively. A simple differential-thermal analysis (DTA)…
A new DTA (Differential Thermal Analysis) device was designed and installed in a Hot Isostatic Pressure (HIP) furnace in order to perform high-pressure thermodynamic investigations up to 2 kbar and 1200C. Thermal analysis can be carried out…
A simple and low cost apparatus has been designed and built to measure the electrical resistivity, ($\rho$), of metal and semiconductors in 300-620 K temperature range. The present design is suitable to do measurement on rectangular bar…
We have developed a new micro-fabricated platform for the measurement of the specific heat of low heat capacity mg-sized metallic samples, such as superconductors, down to temperatures of as low as $10\,\mathrm{mK}$. It addresses…
For modern Gas sensors, high sensitivity and low power are expected. This paper discusses design, simulation and fabrication of new Micromachined Thermal Converters (MTCs) based on GaAs developed for Gas sensors. Metal oxide gas sensors…
The specific heat of toluene in glass and crystal states, has been measured both at low temperatures down to 1.8 K (using the thermal relaxation method) and in a wide temperature range up to the liquid state (using a quasiadiabatic…
We describe a simple and accurate differential thermal analysis set up to measure the latent heat of solid state materials undergoing abrupt phase transitions in the temperature range from 77 K to above room temperature. We report a…
In this work, we report the fabrication of experimental setup for high temperature thermal conductivity ($\kappa$) measurement. It can characterize samples with various dimensions and shapes. Steady state based axial heat flow technique is…
Temperature gradients developed at ultra-high temperatures create a challenge for temperature measurements that are required for material processing. At ultra-high temperatures, the components of the system can react and change phases…
We developed a metallic pressure cell made of nickel-chromium-aluminum (NiCrAl) for use with a non-destructive pulse magnet and a magnetic susceptibility measurement apparatus with a proximity detector oscillator (PDO) in pulsed magnetic…
Thermalized elastic membranes without distant self-avoidance are believed to undergo a crumpling transition when the microscopic bending stiffness is comparable to $kT$, the scale of thermal fluctuations. Most potential physical…
Various techniques can be employed to determine the temperature of magnetic transformation, whether it be the Curie or Neel temperature. The standard procedure typically involves creating alloys with defined compositions and performing…