相关论文: Method for control gas diffusion and bubbles forma…
Long fiber composite materials can be elaborated by Liquid Composite Molding (LCM), a family of processes where fibrous preforms are injected by a low viscosity resin. During this process, we have to pay particular attention to the void…
Compressing a porous, fluid-filled material will drive the interstitial fluid out of the pore space, as when squeezing water out of a kitchen sponge. Inversely, injecting fluid into a porous material can deform the solid structure, as when…
A novel concept of a measurement technology for the localization and determination of the size of gas bubbles is presented, which is intended to contribute to a further understanding of the dynamics of efficiency-reducing gas bubbles in…
The filtration of fluid in 2D porous medium is simulated by the molecular dynamics technique. The high concentration of fluid is created at the initial point in time and the number of fluid particles is investigated in all porous. The…
Flows enabled by phoretic mechanisms are of significant interest in several biological and biomedical processes, such as bacterial motion and targeted drug delivery. Here, we develop a homogenization-based macroscopic boundary condition…
We use a rigid axisymetric microfluidic flow focusing device to produce monodisperse bubbles, dispersed in a surfactant solution. The gas volume fraction of the dispersion collected out of this device can be as large as 90%, demonstrating…
Liquid drops can be kept from touching a plane solid surface by a gas stream entering from underneath, as it is observed for water drops on a heated plate, kept aloft by a stream of water vapor. We investigate the limit of small flow rates,…
'A basic and basically unsolved problem in fluid dynamics is to determine the evolution of rising bubbles and falling drops of one miscible liquid in another' [1]. Here, we address this important literature gap and present the first theory…
The Muskat problem involves filtration of two incompressible fluids throughout a porous medium. In this paper we shall discuss in 3-D the relevance of the Rayleigh-Taylor condition, and the topology of the initial interface, in order to…
Underground gas storage is a critical technology in global efforts to mitigate climate change. In particular, hydrogen storage offers a promising solution for integrating renewable energy into the power grid. When injected into the…
Every year, about 4 million people die from upper respiratory infections. Mask-wearing is crucial in preventing the spread of pathogen-containing droplets, which is the primary cause of these illnesses. However, most techniques for mask…
Slow flow of a single fluid through a porous medium is well understood on a macroscopic level through Darcy's law, a linear relation between flow rate and a combination of pressure differences, viscosity, and gravitational forces. Two-phase…
In particle-laden flows through porous media, porosity and permeability are significantly affected by the deposition and erosion of particles. Experiments show that the permeability evolution of a porous medium with respect to a particle…
The evolution of pulsed discharge behavior inside a preformed air bubble in water from the first to subsequent pulses was experimentally investigated using a synchronized needle to bubble system. A positive nanosecond high-voltage pulsed…
Diffusion in an evolving environment is studied by continuos-time Monte Carlo simulations. Diffusion is modelled by continuos-time random walkers on a lattice, in a dynamic environment provided by bubbles between two one-dimensional…
The release of a gas limited by surface desorption, or by diffusion from the bulk of spherical pebbles is revisited. A method is proposed to identify the release limiting process, by comparing a partial temperature ramp, up to slightly…
We report a 2D Boundary Element Method (BEM) modeling of the thermal diffusion-controlled growth of a vapor bubble attached to a heating surface during saturated pool boiling. The transient heat conduction problem is solved in a liquid that…
The mathematical up-scaling of gas-liquid bubbly flows was carried out under the framework of the volume averaging theory. A two-fluid model and its associated closure problem were deduced. The closure problem was solved for a case study: a…
The production of small fluid droplets relies on an instability of solutions to the Young-Laplace equation. We ask whether smaller droplets can be produced by changing the shape of the nozzle. At a given critical pressure, the circular…
Aqueous foams are solid materials composed of gases and liquids, exhibiting a large gas/liquid surface area and enabling dynamic exchanges between their fluid components. The structure of binary-gas foams, whose bubbles consist of a mixture…