相关论文: Distributed Can-Bus Based Beam Diagnostic System f…

Directional detection of non-baryonic Dark Matter requires 3D reconstruction of low energy nuclear recoils tracks. A gaseous micro-TPC matrix, filled with either 3He, CF4 or C4H10 has been developed within the MIMAC project. A dedicated…

Isolated, short dispersed pulses of radio emission of unknown origin have been reported and there is strong interest in wide-field, sensitive searches for such events. To achieve high sensitivity, large collecting area is needed and…

A longitudinal beam properties, data acquisition system has been commissioned to operate in the Fermilab booster ring. This system captures real time information including beam synchronous phase, bunch length, and coupled bunch instability…

Nowadays with the help of advanced technology, modern vehicles are not only made up of mechanical devices but also consist of highly complex electronic devices and connections to the outside world. There are around 70 Electronic Control…

Diffuse correlation spectroscopy (DCS) is a noninvasive optical technique that probes microvascular blood flow in deep tissues. Here, we present and validate a new on-chip hardware correlator for high-speed DCS measurements. The correlator…

We introduce a flexible, software-defined real-time multi-modulation format receiver implemented on an off-the-shelf general-purpose graphics processing unit (GPU). The flexible receiver is able to process 2 GBaud 2-, 4-, 8-, and 16-ary…

In 1995 a 9SDH-2 Pelletron from NEC was installed at IFUNAM (Instituto de Fisica, Universidad Nacional Autonoma de Mexico). Two beam lines have been operational since then and two new lines have been built. In order to perform the planned…

The control system of the VEPP-4 facility was designed more than fifteen years ago and based on the home-developed CAMAC-embedded minicomputers Odrenok [1]. Five years ago, all computers were connected via Ethernet network. This step…

Modern vehicles are complex cyber-physical systems made of hundreds of electronic control units (ECUs) that communicate over controller area networks (CANs). This inherited complexity has expanded the CAN attack surface which is vulnerable…

The development of intrusion detection systems (IDS) for the in-vehicle Controller Area Network (CAN) bus is one of the main efforts being taken to secure the in-vehicle network against various cyberattacks, which have the potential to…

A prototype flash analog-to-digital readout system for cosmic ray detection at energies below 10^18 eV has been designed and tested at Columbia University Nevis Laboratories. The electronics consist of an FADC module that digitizes 16…

Although CMS will not start operation for several years, many subdetector groups have active testbeam programs involving final or near-final electronics. The high-bandwidth electronics require the development of new DAQ systems including…

A new data acquisition program for personal computers with Windows operating system has been built at Charles University van de Graaff laboratory. It allows fast data acquisition from CAMAC and other PC interface cards using interrupt or…

A Dual Digital Signal Processing VME Board was developed for the Continuous Electron Beam Accelerator Facility (CEBAF) Beam Current Monitor (BCM) system at Jefferson Lab. It is a versatile general-purpose digital signal processing board…

An upgraded Beam Emission Spectroscopy (BES) system has been deployed to access low amplitude turbulence regions near internal transport barriers on the DIII-D tokamak. Sixteen high sensitivity channels are being installed. A significant…

Recent years have seen an exponential rise in complex software-driven functionality in vehicles, leading to a rising number of electronic control units (ECUs), network capabilities, and interfaces. These expanded capabilities also bring-in…

With advancements in technology, the smaller versions of satellites have gained momentum in the space industry for earth monitoring and communication-based applications. The rise of CanSat technology has significantly impacted the space…

Additive Manufacturing (AM) is gaining renewed popularity and attention due to low-cost fabrication systems proliferating the market. Current communication protocols used in AM limit the connection flexibility between the control board and…

An FPGA based digital signal processing (DSP) system for biasing and reading out multiplexed bolometric detectors for mm-wavelength telescopes is presented. This readout system is being deployed for balloon-borne and ground based cosmology…

The doubly selective (DS) channel estimation in the large-scale multiple-input multiple-output (MIMO) systems is a challenging problem due to the large number of the channel coefficients to be estimated, which requires unaffordable and…