相关论文: Fracture Patterns Induced by Desiccation in a Thin…
We introduce a model for the dynamics of mud cracking in the limit of of extremely thin layers. In this model the growth of fracture proceeds by selecting the part of the material with the smallest (quenched) breaking threshold. In…
Volume alteration in solid materials is a common cause of material failure. Here we investigate the crack formation in thin elastic layers attached to a substrate. We show that small variations in the volume contraction and substrate…
The properties of slow crack growth in brittle materials are analyzed both theoretically and experimentally. We propose a model based on a thermally activated rupture process. Considering a 2D spring network submitted to an external load…
We present a detailed study of a two-dimensional minimal lattice model for the description of mud cracking in the limit of extremely thin layers. In this model each bond of the lattice is assigned to a (quenched) breaking threshold.…
Cracks in thin layers are influenced by what lies beneath them. From buried craters to crocodile skin, crack patterns are found over an enormous range of length scales. Regardless of absolute size, their substrates can dramatically…
The fracture mechanics was widely employed to explain the crack propagation in the deposition produced by drying colloidal suspension. However, more complex than conventional fracture, those cracks periodically distribute and make up a…
Drying induced cracking of concrete surfaces and repair layers is a common problem. A principal cause for this type of cracking is the moisture and resulting contraction gradient that develops in the cement paste matrix upon drying. This…
Superficial (two dimensional) crack patterns appear when a thin layer of material elastically attached to a substrate contracts. We study numerically the maturation process undergone by these crack patterns when they are allowed to adapt in…
Fracture in quasi-statically driven systems is studied by means of a discrete spring-block model. Developed from close comparison with desiccation experiments, it describes crack formation induced by friction on a substrate. The model…
Cracking and peeling of a layer of clay on desiccation has been simulated using a spring model. A vertical section through the layer with finite thickness is represented by a rectangular array of nodes connected by linear springs on a…
We investigate the formation of spiral crack patterns during the desiccation of thin layers of precipitates in contact with a substrate. This symmetry-breaking fracturing mode is found to arise naturally not from torsion forces, but from a…
We have studied shrinkage crack patterns which form when a thin layer of an alumina/water slurry dries. Both isotropic and directional drying were studied. The dynamics of the pattern formation process and the geometric properties of the…
When cracks form in a thin contracting layer, they sequentially break the layer into smaller and smaller pieces. A rectilinear crack pattern encodes information about the order of crack formation, as later cracks tend to intersect with…
Polygonal desiccation crack patterns are commonly observed in natural systems. Despite their quotidian nature, it is unclear whether similar crack patterns which span orders of magnitude in length scales share the same underlying physics.…
We review microstructural fracture growth models suitable for the study of hydraulic fracture processes in disordered porous materials and present some basic results. It is shown that microstructural models exhibit certain similarities to…
Straight cracks are observed in thin coatings under residual tensile stress, resulting into the classical network pattern observed in china crockery, old paintings or dry mud. Here, we present a novel fracture mechanism where delamination…
Starch-water slurries are commonly used to study fracture dynamics. Drying starch-cakes benefit from being simple, economical, and reproducible systems, and have been used to model desiccation fracture in soils, thin film fracture in paint,…
A study of crack patterns in laponite films of different thickness is presented. Two cracking regimes are observed. The earlier with a higher rate of desiccation and shrinking has predominantly four-fold vertices in the crack network, while…
As a consequence of shearing, wing cracks can emerge from pre-existing fractures. The process involves the interaction of sliding of the existing fracture surfaces and the tensile material failure that creates wing cracks. This work devises…
In this paper, we'll answer several abstract, formal questions about the nature of crack growth and nucleation. Bringing a field theory point of view to fracture illuminates things in what I hope will be an entertaining way. Formally, what…