相关论文: Optimization of target film materials and protecti…
The neutron shielding properties of high-density concrete and magnetite aggregates were evaluated using both experimental measurements and Monte Carlo simulations. Because these materials are commonly used in medical accelerator facilities,…
Nanocrystalline metals are promising radiation tolerant materials due to their large interfacial volume fraction, but irradiation-induced grain growth can eventually degrade any improvement in radiation tolerance. Therefore, methods to…
We report the first preparation of nanoporous Al-Mg alloy films by selective dissolution of Mg from a Mg-rich AlxMg1-x alloy. We show how to tune the stoichiometry, the porosity and the oxide contents in the final film by modulating the…
Chemically inert Coatings on Havar entrance foils of the targets for [18F] production via proton irradiation of enriched water at pressurized conditions are needed to decrease the amount of ionic contaminants released from Havar. In order…
The prospects of using nanofilms of indium-containing III-V semiconductors, gold and single-layer graphene in magnetic field sensors, intended for application in radiation environment were evaluated on the results of testing in neutron…
We report the growth by molecular beam epitaxy of highly resistive GdN, using intentional doping with magnesium. Mg-doped GdN layers with resistivities of 1000 {\Omega}.cm and carrier concentrations of 10E16 cm-3 are obtained for films with…
Particle-producing targets in high-energy research facilities are often made from refractory metals, and they typically require dedicated cooling systems due to the challenging thermomechanical conditions they experience. However, direct…
We present the first investigation on the effect of highly charged ion bombardment on a manganese arsenide thin film. The MnAs films, 150 nm thick, are irradiated with 90 keV Ne$^{9+}$ ions with a dose varying from $1.6\times10^{12}$ to…
Materials are subjected to energetic particles in a number of radiation environments,and are hence prone to undesirable (radiation) damage.We report here the superiority of the nanocrystalline phase over bulk for radiation tolerance under…
Here we demonstrate nanometer thick iron garnet films suitable for the magneto-optical applica-tions. Bismuth-substituted iron garnet films of compositions Bi{_1}Y{_2}Fe{_5}O{_{12}} and Bi{_1}Tm{_2}Fe{_5}O{_{12}} deposited on gadolinium…
Magnesium (Mg) has the lowest density of all structural metals and has excellent potential for wide use in structural applications. While pure Mg has inferior mechanical properties; the addition of further elements at various concentrations…
Magnesium alloys are emerging as promising alternatives to traditional orthopedic implant materials thanks to their biodegradability, biocompatibility, and impressive mechanical characteristics. However, their rapid in-vivo degradation…
Magnetic garnets such as yttrium iron garnet (Y$_3$Fe$_5$O$_{12}$, YIG) are widely used in spintronic and magnonic devices. Their magnetic and magneto-optical properties can be modified over a wide range by tailoring their chemical…
The study uses AACVD technology with nitrogen carrier gas to make AZO thin films through which it determines structural, optical, and morphological changes from 0 to 20 percent aluminum doping. The depositions took place at 400 degrees…
The effects of neutron irradiation on normal state and superconducting properties of epitaxial magnesium diboride thin films are studied up to fluences of 1020 cm-2. All the properties of the films change systematically upon irradiation.…
Contemporary ultraintense, short-pulse laser systems provide extremely compact setups for the production of high-flux neutron beams, such as those required for nondestructive probing of dense matter, research on neutron-induced damage in…
Nitride materials, valued for their structural stability and exceptional physical properties, have garnered significant interest in both fundamental research and technological applications. The fabrication of high-quality nitride thin films…
In the present work, a thin film was deposited on quartz substrate by reactive RF magnetron sputtering of high purity (99.999%) aluminium target using ultra-high pure (Ar + N2) gas mixture. The percentage ratio of Ar and N2 in the gas…
The production of 225Ac using either a proton or electron accelerator requires a target of 226Ra. Radium metal is difficult to work with and so a radium salt, such as radium carbonate, is preferred as a target material. Normally available…
The TUCAN (TRIUMF Ultra-Cold Advanced Neutron) collaboration aims to search for the neutron electric dipole moment (nEDM) with unprecedented precision. One of the essential elements for the nEDM measurement is a polarization analyzer of…