相关论文: Analytic Design of Flat-Wire Inductors for High-Cu…
Power converters inherently display non-linear load characteristics, resulting in a high level of mains harmonics, and hence the necessity of implementing Power Factor Correction (PFC). Active PFC circuitry typically comprises an inductor…
DC-DC converters with galvanic isolation are a key element in the aircraft DC distribution system and Dual and Triple Active Bridge converters are one of the most interesting candidates in this application. The high-frequency transformer…
Extensive research papers of three-dimensional computational techniques are widely used for the investigation of human brain pathophysiology. Eddy current analyzing could provide an indication of conductivity change within a biological…
Magneto-mechanical transmitters offer a compact and low-power solution for the generation of ultra-low frequency (ULF) magnetic signals for through-ground and through-seawater communications. Resonant arrays of smaller magneto-mechanical…
One of the popular impedance-network converters are Y-source converters which along with their essential characteristics such as reducing the size of converter components, single-stage power transferring, fault tolerance, and wide voltage…
Flux loops have been installed on selected segments of the magnetic flux return yoke of the 4 T superconducting coil of the Compact Muon Solenoid (CMS) detector under construction at CERN. Voltages induced in the loops during discharge of…
In automotive power electronics, distortion and electromagnetic interference (EMI) generated by the switching action of power semiconductors can be a significant challenge for the design of a compact, lightweight vehicle. As semiconductor…
As a result of improvements in power semiconductors, moderate frequency switching supplies can now provide the hundreds of amps typically required by accelerators with zero-to-peak noise in the kHz region ~0.06% in current or voltage mode.…
A novel radial-flux eddy-current coupler with interior permanent magnets (IPM) is proposed, providing higher demagnetization tolerance, making it well-suited for applications with limited accessibility, such as offshore wind generation.…
Axial flux permanent magnet designs are compact and becoming an attractive design for electric vehicles as an auxiliary braking system. This work develops the design of an Axial Flux Permanent Magnet Eddy current brake for application on…
Eddy current flow meters (ECFM) are widely used for measuring the flow velocity of electrically conducting fluids. Since the flow induced perturbations of a magnetic field depend both on the geometry and the conductivity of the fluid,…
We use a radio-frequency $^{85}$Rb alkali-vapor cell magnetometer based on a paraffin-coated cell with long spin-coherence time and a small, low-inductance driving coil to create highly resolved conductivity maps of different objects. We…
In this paper, a high frequency transformer with different conductors and winding arrangements, at presence of eddy currents and skin effect, is studied. By using different winding structures, and conductor types, such as circular, square…
The transient response from a transmitter-receiver coil system inside a multi-layer cylindrical conductive configuration is obtained. The particular set-up applies to well logging as well as to eddy current tube testing. In this work, a…
Representations of AC power systems by frequency dependent impedance equivalents is an emerging technique in the dynamic analysis of power systems including power electronic converters. The technique has been applied for decades in DC-power…
Power cables have complex geometries in order to reduce their ac resistance. Although there are many different cable designs, most have in common that their inner conductors' cross-section is divided into several electrically insulated…
This paper presents a first assessment of a design method aiming at the minimization of the number of turns $N$ and the air gap length $g$ in ferrite-core based low-frequency-current biased AC filter inductors. Several design cases are…
On-silicon inductors using a bulk 0.18 {\mu}m CMOS process have been designed. By shunting different metal layers in parallel, inductor values and quality factors were simulated. Selected inductors were then employed in two open-loop buck…
The inductance/impedance due to thin metallic structures in non-destructive testing (NDT) is difficult to evaluate. In particular, in Finite Element Method (FEM) eddy current simulation, an extremely fine mesh is required to accurately…
A family of interleaved current-fed high step-up dc-dc converters are introduced and analyzed here by combining a voltage multiplier (VM) and an active clamp circuit for high-voltage high-power applications. Low input currents and output…