相关论文: CuIn(Se,Te)2 absorbers with bandgaps < 1 eV for bo…
Tandem solar cells can better harness the energy of the solar spectrum. Chalcopyrite solar cells have drawn attention, being the only highly efficient devices with bandgap around 1.0 eV, suitable for bottom cells. In the quest for better…
Power-conversion efficiency is a critical factor for the wider adoption of solar-cell modules. Thin-film solar cells are cheap and easy to manufacture, but their efficiencies are low compared to crystalline-silicon solar cells and need to…
Reducing the thickness of Cu(In,Ga)Se2 solar cells is a key objective in order to reduce production cost and to improve sustainability. The major challenge for sub-micron Cu(In,Ga)Se2 cells is the recombination at the backside. In standard…
Wide-gap Cu(In,Ga)S2 solar cells with In2O3:Sn (ITO) as transparent back contact are evaluated for the application as top cells in tandem devices. The effect of Na on the solar cell performance is investigated by supplying additional Na by…
Record efficiency in chalcopyrite-based solar cells Cu(In,Ga)(S,Se)2 is achieved using a gallium gradient to increase the band gap of the absorber towards the back side. Although this structure has successfully reduced recombination at the…
A coupled optoelectronic model was implemented along with the differential evolution algorithm to assess the efficacy of grading the bandgap of the CZTSSe layer for enhancing the power conversion efficiency of thin-film CZTSSe solar cells.…
In$_2$Se$_3$ in the three-dimensional (3D) hexagonal crystal structure with space group $P6_1$ ($\gamma$-In$_2$Se$_3$) has a direct band gap of $\sim$1.8 eV and high absorption coefficient, making it a promising semiconductor material for…
We demonstrate four and two-terminal perovskite-perovskite tandem solar cells with ideally matched bandgaps. We develop an infrared absorbing 1.2eV bandgap perovskite, $FA_{0.75}Cs_{0.25}Sn_{0.5}Pb_{0.5}I_3$, that can deliver 14.8 %…
Recent technical and commercial successes of existing thin film solar cell technologies motivates exploration of next-generation photovoltaic (PV) absorber materials. Of particular scientific interest are compounds like CuSbSe$_2$, which do…
We present direct measurements of depth-resolved band gap variations of CuIn(1-x)Ga(x)Se2 thin-film solar cell absorbers. A new measurement technique combining parallel measurements of local thin-film interference and spectral…
Alloying small quantities of silver into Cu(In,Ga)Se2 was shown to improve the efficiency for wide and low band gap solar cells. We study low band gap industrial Cu(In,Ga)(S,Se)2 absorbers, substituting less than 10% of the copper with…
In this article, we demonstrate CdSe-CuSbSe2-based double junction two-terminal tandem solar cells simulated with SCAPS-1D. The highest performance of the tandem cell has been confirmed by optimizing the electrical and optical properties of…
The development of tandem photovoltaics and photoelectrochemical solar cells requires new absorber materials with band gaps in the range of ~1.5-2.3 eV, for use in the top cell paired with a narrower-gap bottom cell. An outstanding…
We simulated photovoltaic characteristics of single heterojunction solar cell with Cu2ZnSnS4 and Cu2ZnSnSe4 absorber layer numerically using one dimensional solar cell capacitance simulator (SCAPS-1D). n-CdS/ZnO double buffer layer is used…
CdTe is the most commercially successful thin-film photovoltaic technology to date. The recent development of Se-alloyed CdSe$_{x}$Te$_{1-x}$ layers in CdTe solar cells has led to higher device efficiencies, due to a lowered bandgap…
An optoelectronic optimization was carried out for an AlGaAs solar cell containing (i) an n-AlGaAs absorber layer with a graded bandgap and (ii) a periodically corrugated Ag backreflector combined with localized ohmic Pd-Ge-Au backcontacts.…
The Cu-deficient CuxInSe2 (x larger than 0.3) phase can be stabilized as a thin film. A uniform Cu-deficient composition with a chalcopyrite structure was obtained by the precision engineering of a two-step synthesis process involving…
A high theoretical efficiency of 47.2% was achieved by a novel combination of In0.51Ga0.49P, GaAs, In0.24Ga0.76As and In0.19Ga0.81Sb subcell layers in a simulated quadruple junction solar cell under 1 sun concentration. The electronic…
Sulfide chalcopyrite, Cu(In,Ga)S2, having wide bandgap (larger than 1.5 eV), favorable optoelectronic properties, and high stability, is a promising top-cell absorber for tandem applications. Adapting device structures optimized for 1.0 -…
Following the recent success of monolithically integrated Perovskite/Si tandem solar cells, great interest has been raised in searching for alternative wide bandgap top-cell materials with prospects of a fully earth-abundant, stable and…