相关论文: Cutting and tearing thin elastic sheets: two novel…
Recent experiments have imposed controlled swelling patterns on thin polymer films, which subsequently buckle into three-dimensional shapes. We develop a solution to the design problem suggested by such systems, namely, if and how one can…
The reliability of processes with moving elastic and isotropic material containing initial cracks is considered in terms of fracture. The material is modelled as a moving plate which is simply supported from two of its sides and subjected…
We perform fracture experiments on nanoscale phase separated glasses and measure crack surface roughness by atomic force microscopy. The ability of tuning the phase domain size by thermal treatment allows us to test thoroughly the…
I study the influence of temperature and the crack-tip velocity of the bond breaking at the crack tip in rubber-like materials. The bond breaking is considered as a stress-aided thermally activated process and result in an effective crack…
We study the roughness of a crack interface in a sheet of paper. We distinguish between slow (sub-critical) and fast crack growth regimes. We show that the fracture roughness is different in the two regimes using a new method based on a…
In this paper, we prove a new existence result for a variational model of crack growth in brittle materials proposed in [15]. We consider the case of $n$-dimensional finite elasticity, for an arbitrary $n\ge1$, with a quasiconvex bulk…
Volume alteration in solid materials is a common cause of material failure. Here we investigate the crack formation in thin elastic layers attached to a substrate. We show that small variations in the volume contraction and substrate…
Taking into account stress fluctuations due to thermal noise, we study thermally activated irreversible crack growth in disordered media. The influence of material disorder on sub-critical growth of a single crack in two-dimensional brittle…
Brittle fracturing of materials is common in natural and industrial processes over a variety of length scales. Knowledge of individual particle dynamics is vital to obtain deeper insight into the atomistic processes governing crack…
The fracture toughness for a mode I/II crack propagating in a ductile material has been subject to numerous investigations. However, the influence of the material hardening law has received very limited attention, with isotropic hardening…
We present experiments and simulations on cyclically sheared colloidal gels, and probe their behaviour on several different length scales. The shearing induces structural changes in the experimental gel, changing particles' neighborhoods…
This article present the double-periodical lattice made of infinite elastic fibers that withstand bending and tension. The model describes the elastic properties of flat periodic structure. With this model the behavior of a two-dimensional…
We examine the fracture mechanics of tearing graphene. We present a molecular dynamics simulation of the propagation of cracks in clamped, free-standing graphene as a function of the out-of-plane force. The geometry is motivated by…
This work is devoted so show the appearance of different cracking modes in linearly elastic thin film systems by means of an asymptotic analysis as the thickness tends to zero. By superposing two thin plates, and upon suitable scaling law…
In this paper, the effect of twin boundaries on the crack growth behaviour of single crystal BCC Fe has been investigated using molecular dynamics simulations. The growth of an atomically sharp crack with an orientation of (111)$<$110$>$…
The process of crumpling a sheet and compacting it into a ball is dependent on many parameters that are difficult to disentangle. We study the effect of plasticity on the crumpling process, and disentangle the effects of plasticity and…
Elastic waves scattering off a periodic single and double array of thin cylindrical defects is considered for isotropic materials. An analytical expression for the scattering matrix is obtained by means of the Lippmann-Schwinger formalism…
Stochastic models for the development of cracks in 1 and 2 dimensional objects are presented. In one dimension, we focus on particular scenarios for interacting and non-interacting fragments during the breakup process. For two dimensional…
When one slightly pushes a thin elastic sheet at its center into a hollow cylinder, the sheet forms (to a high degree of approximation) a developable cone, or "d-cone" for short. Here we investigate one particular aspect of d-cones, namely…
Growth and folding in one-layered model tissue sheets are studied in a stochastic, lattice-free single cell model which considers the discrete cellular structure of the tissue, and a coarse grained analytical approach. The polarity of the…