相关论文: A model updating procedure to enhance structural a…

This paper presents a new numerical procedure for evaluating the vibration frequencies and mode shapes of masonry buildings in the presence of cracks. The algorithm has been implemented within the NOSA-ITACA code, which models masonry as a…

Finite element model updating of a structure made of linear elastic materials is based on the solution of a minimization problem. The goal is to find some unknown parameters of the finite element model (elastic moduli, mass densities,…

A novel method for performing model updating on finite element models is presented. The approach is particularly tailored to modal analyses of buildings, by which the lowest frequencies, obtained by using sensors and system identification…

We present an effcient Monte-Carlo method for lattice glass models which are characterized by hard constraint conditions. The basic idea of the method is similar to that of the $N$-fold way method. By using a list of sites into which we can…

We apply a new updating algorithm scheme to investigate the critical behavior of the two-dimensional ferromagnetic Ising model on a triangular lattice with nearest neighbour interactions. The transition is examined by generating accurate…

Structural optimization (topology, shapes, sizing) is an important tool for facilitating the emergence of new concepts in structural design. Normally, topology optimization is carried out at the early stage of design and then shape and…

A new method for examining the possible space-time variation of the fine structure constant ($\alpha$) is proposed. The technique uses a relatively simple measurement with an optical resonator to compare atom-stabilized optical frequency…

In general, there is a mismatch between a finite element model {(FEM)} of a structure and its real behaviour. In aeronautics, this mismatch must be small because {FEM}s are a fundamental part of the development of an aircraft and of…

Thanks to recent advancements in numerical methods, computer power, and monitoring technology, seismic ambient noise provides precious information about the structural behavior of old buildings. The measurement of the vibrations produced by…

Real-world time series often exhibit a non-stationary nature, degrading the performance of pre-trained forecasting models. Test-Time Adaptation (TTA) addresses this by adjusting models during inference, but existing methods typically update…

This article proposes an estimation method to detect breakpoints for linear time series models with their parameters that jump scarcely. Its basic idea owes the group LASSO (group least absolute shrinkage and selection operator). The method…

This paper offers a survey of uppaalsmc, a major extension of the real-time verification tool uppaal. uppaalsmc allows for the efficient analysis of performance properties of networks of priced timed automata under a natural stochastic…

In this paper, a non-probabilistic method based on fuzzy logic is used to update finite element models (FEMs). Model updating techniques use the measured data to improve the accuracy of numerical models of structures. However, the measured…

This paper presents a novel design update strategy for topology optimization, as an iterative optimization. The key contribution lies in incorporating a design updater concept with quantum annealing, applicable to both truss and continuum…

We study whether using non-orthogonal multiple access (NOMA) in the uplink of a mobile network can improve the performance over orthogonal multiple access (OMA) when the system requires ultra-reliable low-latency communications (URLLC). To…

We compare convergence of isogeometric analysis (IGA), a spline modification of finite element method (FEM), with FEM in the context of our real space code for ab-initio electronic structure calculations of non-periodic systems. The…

Structural identifiability analysis of fractional-order equivalent circuit models (FO-ECMs), obtained through electrochemical impedance spectroscopy (EIS) is still a challenging problem. No peer-reviewed analytical or numerical proof does…

In this study, we describe a procedure of topology optimization in the framework of the linear Boltzmann equation, implemented using a reference Monte-Carlo particle transport code. This procedure can design complex structures that optimize…

While purely data-driven assessment is feasible for the first levels of the Structural Health Monitoring (SHM) process, namely damage detection and arguably damage localization, this does not hold true for more advanced processes. The tasks…

In this paper, we focus on modelling the timing aspects of binary programs running on architectures featuring caches and pipelines. The objective is to obtain a timed automaton model to compute tight bounds for the worst-case execution time…