相关论文: Crystal Hybridized Pyro-Piezoelectric Ferrofluidic…
Narrow bandwidth and easy detuning, inefficiency in broadband and non-stationary excitations, and difficulties in matching linear harvester's resonance frequency to low-frequency excitations at small scales, have convinced the researchers…
In this study, we design the 3D-printed phononic crystal (PnC) beam with the topological interface state for harvesting the mechanical energy of flexural waves. The PnC beam is formed by arranging periodic grooves on its surface. The PnC…
Quantum materials have exhibited attractive electro-mechanical responses, but their piezoelectric coefficients are far from satisfactory due to the lack of fundamental mechanisms to benefit from the quantum effects. We discovered the valley…
Layered ferromagnetic-piezoelectric composites show mechanical strain mediated electromagnetic coupling. Here we discuss dielectric and piezoelectric properties of ferrite-lead zirconate titanate (PZT) and lanthanum manganite-PZT samples.…
The full architecture of an electrostatic kinetic energy harvester (KEH) based on the concept of near-limits KEH is reported. This concept refers to the conversion of kinetic energy to electric energy, from environmental vibrations of…
Overloaded vehicles are the primary cause of accelerated degradation of road infrastructures. In this context, although weigh-in-motion (WIM) systems are most efficient to enforce weight regulations, current technologies require costly…
Polytetrafluoroethylene can be considered as a model for calorimetric studies of complex systems with thermodynamics transitions at ambient temperature. This polymer exhibits two phase transitions of different nature at 292 K and 303 K. We…
Piezoelectric PZT solid solutions were studied as a function of pressure and temperature. Moderate pressure is found to induce phase transitions to monoclinic phases (Cm,Cc) for Ti-rich PZT, which are the same ferroelectric phases…
The physical basis for observed long-lived electronic coherence in photosynthetic light-harvesting systems is identified using an analytically soluble model. Three physical features are found to be responsible for their long coherence…
In this work, a 3-D simulation is performed to study for the solid-fluid coupling effect driven by piezoelectric materials and utilizes asymmetric obstacles to control the flow direction. The result of simulation is also verified. For a…
This work introduces a novel methodology to assess the performance of Piezoelectric Energy Harvesters (PEHs) in order to study auxetic enhancement possibilities. For this purpose, a new approach for evaluating the intrinsic effective…
Frequency dependent dynamic behavior in Piezoresponse Force Microscopy (PFM) implemented on a beam-deflection atomic force microscope (AFM) is analyzed using a combination of modeling and experimental measurements. The PFM signal comprises…
This novel piezoelectric zinc oxide (ZnO) thin film microcantilever was fabricated by micromachining technique. To release the cantilever, wet anisotropic etching of Silicon (Si) was performed by tetramethyl ammonium hydroxide (TMAH). The…
An extended use of renewable energies and a trend towards increasing energy consumption lead to challenges such as temporal and spatial decoupling of energy generation and consumption. This work evaluates the possible applications and…
Traditional data collection from sensors produce a lot of data, which lead to constant power consumption and require more storage space. This study proposes an algorithm for a data acquisition and processing method based on Fourier…
A system model is used, describing the voltage-to-voltage transfer function for an ultrasonic transmit-receive transducer pair based on simulations using a finite element model for piezoelectric transducers (FEMP). The piezoelectric ceramic…
Advances in the development of flexible piezoelectric and thermoelectric materials have provided an important avenue for the exploration of energy scavenging through the thermodynamic-coupling of orthogonal energy-scavenging modalities.…
The use of wearable and mobile devices for health monitoring and activity recognition applications is increasing rapidly. These devices need to maximize their accuracy and active time under a tight energy budget imposed by battery and small…
Numerous energy harvesting wireless devices that will serve as building blocks for the Internet of Things (IoT) are currently under development. However, there is still only limited understanding of the properties of various energy sources…
Halide perovskite-based photodiodes are promising for efficient detection across a broad spectral range. Perovskite absorber thin-films have a microcrystalline morphology, characterized by a high density of surface states and defects at…