相关论文: Selective etching of PDMS: etching as positive res…
Two-dimensional (2D) materials are considered for numerous applications in microelectronics, although several challenges remain when integrating them into functional devices. Weak adhesion is one of them, caused by their chemical inertness.…
The corrosion resistance of an electroplated (EP) Zn coating whose surface was chemically etched to produce surface defects (pores) is investigated in this work. Impedance and DC polarisation measururements were employed to study the…
This study investigated the formation of multi-voids in polydimethylsiloxane (PDMS) using a multi-pulse irradiation method and explored the impact of laser energy, number of pulses per micron (writing speed), and laser spot size (NA) on the…
Oil wastewater and spilled oil caused serious environmental pollution and damage to public health in the last years. Therefore, considerable efforts are made to develop sorbent materials able to separate oil from water with high selectivity…
O2-plamsa-based digital etching of Al0.25Ga0.75N with a 0.8 nm AlN spacer on GaN was investigated. At 40 W RF bias power and 40 sccm oxygen flow, the etch depth of Al0.25Ga0.75N was 5.7 nm per cycle. The 0.8 nm AlN spacer layer acted as an…
Chalcogenides have recently emerged as an important class of phase-change materials (PCMs) for nanophotonics, owing to their very high refractive index (RI) and low optical loss in the visible to near-infrared range. They exhibit an…
In this paper we describe a stretchable solid-state electronic switching material that operates at high voltage potentials, as well as a switch material benchmarking technique that utilizes a modular dielectric elastomer (artificial muscle)…
The development of thermal energy storage materials is the most attractive strategy to harvest the solar energy and increase the energy utilization efficiency. Phase change materials (PCMs) have received much attention in this research…
Diamond has recently attracted considerable attention as a promising platform for quantum technologies, photonics and high resolution sensing applications. Here we demonstrate a chemical approach that enables the fabrication of functional…
Inductively Coupled Plasma (ICP) etching of amorphous silicon (a-Si) nanostructures using a continuous C4F8/SF6 plasma over nanotopography in silicon dioxide (SiO2) is investigated. The coil power of the ICP system is used to tune the a-Si…
The growing interest in 3D printing of silica glass has spurred substantial research efforts. Our prior work utilizing a liquid silica resin (LSR) demonstrated high printing accuracy and resolution. However, the resin's sensitivity to…
In this paper we present an improved process for producing elastomer transistor stamps and high-mobility organic field-effect transistors (FETs) based on semiconducting acene molecular crystals. In particular, we have removed the need to…
We present the first application of polysiloxane-based scintillators as active medium in a shashlik sampling calorimeter. These results were obtained from a testbeam campaign of a $\sim$6$\times$6$\times$45 cm$^3$ (13 $X_0$ depth)…
Switchable and active metasurfaces allow for the realization of beam steering, zoomable metalenses, or dynamic holography. To achieve this goal, one has to combine high-performance metasurfaces with switchable materials that exhibit high…
This study presents a prototype D-band waveguide orthomode transducer (OMT) fabricated using chemically etched brass platelets. This method offers a fast, cost-effective, and scalable approach for producing waveguide OMTs above 100 GHz,…
The evolution over time of the non-linear slip behavior of a polydimethylsiloxane (PDMS) polymer melt on a weakly adsorbing surface made of short non-entangled PDMS chains densely end-grafted to the surface of a fused silica prism has been…
We investigate the damping enhancement in a class of biomimetic staggered composites via a combination of design, modeling, and experiment. In total, three kinds of staggered composites are designed by mimicking the structure of bone and…
Monocrystalline silicon solar cells with photo-absorbing morphology can amplify light-trapping properties within the absorber layer and help to fabricate cost-effective solar cells. In this paper, the effect of different parameters namely…
Porous materials are relevant for a broad range of technologies from catalysis and filtration, to tissue engineering and lightweight structures. Controlling the porosity of these materials over multiple length scales often leads to enticing…
A method to create a highly homogeneous magnetic field by applying topology optimized, additively manufactured shimming elements is investigated. The topology optimization algorithm can calculate a suitable permanent and nonlinear soft…