相关论文: Flowing Bottomhole Pressure Calculation for a Pump…
The quantized current generated by a quantum dot pump is calculated numerically. The numerical simulation is done by dividing the time varying potential into many static potentials with a short time interval and calculating the electron…
This paper proposes a novel method to estimate the wheel dynamic load based on the gas pressure of a hydro-pneumatic suspension. A nonlinear coupled model between suspension chamber pressure and tire-ground contact force is developed,…
Direct and noninvasive measurement of the pressure distribution in test sections of a micro-channel is a challenging, if not an impossible, task. Here, we present an analytical method for extracting the pressure distribution in a deformable…
Using hydraulic models in control design in district heating networks can increase pumping efficiency and reduce sensitivity to hydraulic bottlenecks. These models are usually white-box, as they are obtained based on full knowledge of the…
We propose and analyse analogs of optical cavities for atoms using three-well Bose-Hubbard models with pumping and losses. We consider triangular configurations. With one well pumped and one damped, we find that both the mean-field dynamics…
The paper describes capabilities of numerical simulation of liquid flows with solid and/or gas admixtures in centrifugal pumps using modern commercial CFD software packages, with the purpose to predict performance curves of the pumps…
We calculate the average volumetric flux versus pressure drop of bubbles moving in a single capillary tube with varying diameter, finding a square-root relation from mapping the flow equations onto that of a driven overdamped pendulum. The…
We consider a porous mediaum flow in which the gas is initially distributed in the exterior of an empty region (a hole) and study the final stage of the hole-filling process. Hole-filling is asymptotically described by a self-similar…
Bubble growth, departure and sliding in low-pressure flow boiling has received considerable attention in the past. However, most applications of boiling heat transfer rely on high-pressure flow boiling, for which very little is known, as…
The formation of a single bubble from an orifice in a solid surface, submerged in an in- compressible, viscous Newtonian liquid, is simulated. The finite element method is used to capture the multiscale physics associated with the problem…
Weakly ionised plasmas, formed in high enthalpy hypersonic flows, can be actively manipulated via imposed magnetic fields - a concept termed magnetohydrodynamic (MHD) flow control. Imposed MHD effects, within flows which exhibit multiple…
Accurate subsurface reservoir pressure control is extremely challenging due to geological heterogeneity and multiphase fluid-flow dynamics. Predicting behavior in this setting relies on high-fidelity physics-based simulations that are…
A method for calculating the pressure tensor in constant-volume Monte Carlo simulations of convex bodies is presented. In contrast to other approaches, the method requires only an isotropic scaling of the simulation box, and the counting of…
The Discrete Particle Method (DPM) is used to model granular flows down an inclined chute. We observe three major regimes: static piles, steady uniform flows and accelerating flows. For flows over a smooth base, other (quasi-steady) regimes…
When the dynamical data of a system only convey dynamic information over a limited operating range, the identification of models with good performance over a wider operating range is very unlikely. Nevertheless, models with such…
The pressure-driven flow of a suspension of spinning particles in a rectangular channel is studied using an acoustic method. The suspension is made of insulating particles (PMMA) dispersed in a slightly conducting oil (Ugilec + Dielec) and…
Fluid temperature is important for the analysis of the heat transfers in thermal hydraulics. An accurate measurement or estimation of the fluid temperature in multiphase flows is challenging. This is due to that the thermocouple signal that…
The blowdown of high pressure gas in a pressure vessel produces rapid adiabatic cooling of the gas remaining in the vessel. The gas near the wall is warmed by conduction from the wall, producing radial temperature and density gradients that…
Employing a suitable scaling rule in gas-liquid flow can produce dynamically comparable results, which helps in the development of flow models applicable to a wide range of flow conditions and reduces the carbon footprint; however, matching…
Flows of particles through bottlenecks are ubiquitous in nature and industry, involving both dry granular materials and suspensions. However, practical limitations of conventional experimental setups hinder the full understanding of these…