相关论文: Implications of beam phase and RFSUM measured near…
The difference between the rf voltage seen by the beam and the accelerating voltage required to match the rate of change of the Booster magnetic field is used to estimate the energy loss per beam turn. Because the rf voltage (RFSUM) and the…
A feed-forward ramp can be implemented in Booster to compensate the beam energy loss at different beam intensities for the purpose of minimizing the radial error signal. This can be done only when we have a good understanding about the…
It is important to have experimental methods to estimate the maximum beam intensity for the Fermilab Booster as objective input into long term program commitments. An important existing limit is set by the available rf power. This limit is…
Since a wider aperture has been obtained along the Booster beam line, this opens the opportunity for Booster running a higher intensity beam than ever before. Sooner or later, the available RF accelerating voltage will become a new limit…
The transition energy must be crossed in the CERN PS to accelerate proton and ion beams to flat-top energy. A phase jump of the accelerating RF voltage with respect to the phase of the bunches by about 180 degrees minus twice the…
The Fermilab Booster uses multi-turn beam injection with all its cavities phased such that beam sees a net zero RF voltage even when each station is at the same maxi-mum voltage. During beam capture the RF voltage is increased slowly by…
Detrimental beam dynamics effects limit performance of high intensity rapid cycling synchrotrons (RCS) such as the 8 GeV proton Fermilab Booster. Here we report the results of comprehensive experimental studies of various beam intensity…
Twelve pulsed gamma-T quads have been installed in the Booster to provide fast transition crossing. The less time the beam stays in the non-adiabatic period near transition, the less the longitudinal emittance grows. From the past…
The dipole mode synchrotron frequency is a basic beam parameter; it and a few similarly basic quantities measured at small time intervals serve to characterize the longitudinal beam dynamics throughout the acceleration cycle. The effective…
Increasing proton beam power on neutrino production targets is one of the major goals of the Fermilab long term accelerator programs. In this effort, the Fermilab 8 GeV Booster synchrotron plays a critical role for at least the next two…
It is important to improve the frequency tracking between the RF drive and the cavity field for the purpose of reducing longitudinal phase oscillations and increasing the effective accelerating voltage. And this is especially beneficial for…
Interest in free-space optics (FSO) is rapidly growing as a potential solution for the backhaul of next-generation mobile or low-orbit satellite communications. Various techniques have been suggested for employing an intelligent reflecting…
The match between the Linac beam energy and the energy determined by the bending field of the Booster magnets is crucial for rf capture, beam quality, and the transmission efficiency in a Booster cycle. The observation of the injection…
We examine the potential impacts to slip-stacking from a change of the Booster cycle-rate from 15- to 20-Hz. We find that changing the Booster cycle-rate to 20-Hz would greatly increase the slip-stacking bucket area, while potentially…
Massive multiple-input multiple-output (MIMO) is a fundamental enabler to provide high data throughput in next generation cellular networks. By equipping the base stations (BSs) with tens or hundreds of antenna elements, narrow and high…
Two barrier RF systems were fabricated, tested and installed in the Fermilab Main Injector. Each can provide 8 kV rectangular pulses (the RF barriers) at 90 kHz. When a stationary barrier is combined with a moving barrier, injected beams…
In the aspect of longitudinal beam bunching, the bunching strength can be controlled by the RF cavity phase and voltage. However, these machine parameters are different from those that interact with the beam itself. In order to gain control…
High-power hadron accelerators have strict limits on fractional beam loss. In principle, once a high-quality beam is set up in an acceptable state, beam loss should remain steady. However, in practice, there are many trips in operational…
The proton cycle in the SIS100 synchrotron is designed to deliver single bunches with $2\times10^{13}$ particles at 29 GeV. During the cycle beam dynamics near transition energy have to be analyzed to avoid a significant emittance blow-up.…
Electric current fluctuations are one type of unavoidable machine imperfections,and induce magnetic-field perturbations as a source of instabilities in accelerators. This paper presents measurement-based methodology of modeling the…