相关论文: Results of an RF Pulsed Heating Experiment at SLAC

A geometric model based on a spherical Fermi - surface and using the equivalent skin-layer model allows to calculate the surface resistance, which is relevant for the RF power losses in the cavity walls. An exact solution for this…

Laser pulses with a duration of the order of femtoseconds lead to a strong excitation, heating and potentially to ablation of the irradiated material. During the time of strong excitation, the interaction of the atoms and thus the material…

For many new accelerator applications, superconducting radio frequency (SRF) systems are the enabling technology. In particular for CW applications, much effort is being expended to minimize the power dissipation (surface resistance) of…

The Pulsed RF Heating (PRFH) is the well known effect in the development of high gradient accelerating cavities. There is a lot of research dedicated to the tolerable strength of electromagnetic field and the corresponding temperature rise…

Under-vacuum low- and mid-temperature baking revealed beneficial effects on the performance of niobium-made cavities for superconducting radio-frequency (SRF) applications, primarily seen in particle accelerators. Such a baking process is…

Mid-T heat treatments in the range from 250 to 400 C on superconducting radio-frequency (SRF) cavities have been shown to provide high quality factors that rise with applied rf field strength in high frequency, electro-polished (EP),…

Producing high-brightness and high-charge (>100 pC) electron bunches at blowout regime requires ultrashort laser pulses with high fluence. The effects of laser pulse heating of the copper photocathode are analyzed in this paper. The…

We report techniques for the fabrication of multi-zone linear RF Paul traps that exploit the machinability and electrical conductivity of degenerate silicon. The approach was tested by trapping and laser cooling 24Mg+ ions in two trap…

A Temperature mapping (T-map) system for Superconducting Radio Frequency (SRF) cavities consists of a thermometer array positioned precisely on an exterior cavity wall, capable of detecting small increases in temperature; therefore it is a…

We detail experimental results inferring ionization and temperature for warm dense copper plasmas at several times solid density (15 to 25 g/cm$^3$) and temperatures of 10 to 21 eV. Experiments performed at the OMEGA Laser Facility generate…

The heating of the electronic distribution of a copper photocathode due to an intense drive laser pulse is calculated under the two-temperature model using fluences and pulse lengths typical in RF photoinjector operation. Using the finite…

We present ultrafast pump-probe reflectivity and Doppler spectrometry of a silicon target at relativistic laser intensity. We observe an unexpected rise in reflectivity to a peak approximately $\sim$9 ps after the main pulse interaction…

A method of measuring the thickness of steel plates using through transmission of an acoustic pulse is demonstrated. This study has been done on a stainless steel plate with regions of thickness 10:0 mm, 9:8 mm, and 9:6 mm, using broadband…

Superconducting radio-frequency (SRF) thin film cavities on copper substrates are employed in several particle accelerators. However, these SRF cavities historically featured a progressive performance degradation with the accelerating field…

K x-ray emission from copper plasmas produced by 100 fs, 806 nm laser pulses at intensities in the range of 10^15-10^16 W cm^-2 is studied with respect to input laser polarization and target surface conditions. We demonstrate that even…

Single pressure refractive index gas thermometry (SPRIGT) is a novel primary thermometry, jointly developed by TIPC of CAS in China and LNE-Cnam in France. To realize a competitive uncertainty of 0.25 mK for thermodynamic temperature…

Cu is an ubiquitous material used in industry for its great thermal and electrical properties. Studying the high-pressure high temperature properties of copper (Cu) is relevant for nuclear fusion research as projectiles and flyers used in…

We analyze high cadence high resolution observations of a C3.2 flare obtained by AIA/SDO on August 1, 2010. The flare is a long duration event with soft X-ray and EUV radiation lasting for over four hours. Analysis suggests that magnetic…

RF power coupler is one of the key components in superconducting (SC) linac. It provides RF power to the SC cavity and interconnects different temperature layers (1.8K, 4.2K, 70K and 300K). TTF-III coupler is one of the most promising…

We present evidence for strong radiative cooling in a pulsed-power-driven magnetic reconnection experiment. Two aluminum exploding wire arrays, driven by a 20 MA peak current, 300 ns rise time pulse from the Z machine (Sandia National…