相关论文: Design and Construction of the 3.2 Mev Cathode Ass…

A 3.2 MeV injector has been designed and built for the Darht II Project at Los Alamos Lab. The installation of the complete injector system is nearing completion at this time. The requirements for the injector are to produce a 3.2 MeV, 2000…

The second phase accelerator for the Dual Axis Hydrodynamic Test facility (DARHT) is designed to provide an electron beam pulse that is 2 microsec long, 2kA, and 20 MeV in particle energy. The injector provides 3.2 MeV so that the linac…

An all solid-state kicker pulser for a high current induction accelerator (the Dual-Axis Radiographic Hydrodynamic Test facility DARHT-2) has been designed and fabricated. This kicker pulser uses multiple solid state modulators stacked in…

This paper describes the mechanical design of the downstream beam transport line for the second axis of the Dual Axis Radiographic Hydrodynamic Test (DARHT II) Facility. The DARHT-II project is a collaboration between LANL, LBNL and LLNL.…

The 74-cell DARHT-II long-pulse linear induction accelerator (LIA) was commissioned in its final configuration in 2007-2008. The final accelerated beam parameters were 2 kA, and greater than 17 MeV in a pulse flat to better than +/- 1% for…

The beam parameters of complete prototype of the bERLinPro injector that consisted of a lead cathode in an 1.6 cell superconducting cavity were measured. The measurements are discussed in chapter 2 and indicate that the beam emittance is…

An all solid-state kicker modulator for the Dual-Axis Radiographic Hydrodynamic Test facility (DARHT-2) has been designed and tested. This kicker modulator uses multiple solid-state modules stacked in an inductive-adder configuration where…

For the Low Emittance Gun (LEG) project at Paul Scherrer Institute a stable and reliable high voltage pulsed generator was needed in order to study low emittance beams generation and transport. The system had to provide variable asymmetric…

A novel, induction type linear accelerator, the Neutralized Drift Compression eXperiment (NDCX-II), is currently being commissioned at Berkeley Lab. This accelerator is designed to deliver intense (up to 3x1011 ions/pulse), 0.6 to ~600 ns…

Dual-phase liquid xenon time projection chambers are the core detector elements of many experiments that conduct searches for Dark Matter and rare events, as well as in neutrino and high-energy physics. As part of this detector technology,…

The design of the Linac Coherent Light Source assumes that a low-emittance, 1-nC, 10-ps beam will be available for injection into the 15-GeV linac. The proposed rf photocathode injector that will provide a 150-MeV beam with rms normalized…

The Proton Improvement Plan, Stage Two (PIP-II) is a program of upgrades proposed for the Fermilab injection complex, which central part is an 800 MeV, 2 mA CW SRF linac. A prototype of the PIP-II linac front end called PIP-II Injector Test…

The 10 MeV accelerator-driven subcritical system (ADS) Injector-I test stand at Institute of High Energy Physics (IHEP) is a testing facility dedicated to demonstrate one of the two injector design schemes [Injector Scheme-I, which works at…

The accelerator for the APT Project is a 100 mA CW proton linac with an output energy of 1030 MeV. A High Energy Beam Transport (HEBT) conveys the beam to a raster expander, that provides a large rectangular distribution at a target/blanket…

A device has been built and tested, in which a ceramic superconducting cathode and a copper anode cause electrical discharges in low pressure gases, at temperatures between 50 and 70 K. The electrodes are connected to a capacitors array…

Beam stoppers are installed in the transfer lines of the CERN accelerator complex; these components are used as part of the access safety system, which guarantees the safety of workers in the accelerators. They are designed to stop one or…

We present the design and performance characterization of an external cavity diode-laser system optimized for high stability, low passive spectral linewidth, low cost, and ease of in-house assembly. The main cavity body is machined from a…

The Warm Front End (WFE) of the Proton Improvement Plan II Injector Test at Fermilab has been constructed to its full length. It includes a 15-mA DC, 30-keV H- ion source, a 2 m-long Low Energy Beam Transport (LEBT) with a switching dipole…

ALDO2 is a multi-function, adjustable, low dropout linear regulator designed in onsemi I3T80 0.35~$\mu$m HV CMOS technology for use in HEP detectors that adopt silicon photomultipliers (SiPMs). The chip features four independent regulators,…

The 75-keV injector and 6.7-MeV RFQ that comprise the first portion of the cw, 100-mA proton linac for the accelerator production of tritium (APT) project have been built and operated. The LEDA RFQ has been extensively tested for pulsed and…