相关论文: Microstructure evolution and mechanical behavior o…
A correlation is established between the macro-scale friction regimes of metals and a transition between two dominant atomistic mechanisms of deformation. Metals tend to exhibit bi-stable friction behavior -- low and converging or high and…
Austenitic stainless steels with low carbon have exceptional mechanical properties and are capable to reduce embrittlement, due to high chromium and nickel alloying, thus they are very attractive for efficient energy production in extreme…
Progress in the emerging fields of atomic and close-to-atomic scale manufacturing is underpinned by enhanced precision and optimization of laser-controlled nanostructuring. Understanding thin films' crystallographic orientations and…
Fast directional solidification during Laser Additive Manufacturing (LAM) produces a complex microstructure in nickel-based superalloys, comprising columnar grains with cellular sub-grain structures and carbides. Using non-destructive…
Fe-Co alloys with induced tetragonal strain are promising materials for rare-earth-free permanent magnets. However, as ultrathin-film studies have shown, tetragonal Fe-Co structures tend to a rapid relaxation toward a cubic structure as the…
Crystal structures and microstructural features, such as structural phase transitions, defect structures, chemical and structural inhomogeneities, are known to have profound effects on the physical properties of superconducting materials.…
Understanding grain-boundary mobility during spark plasma sintering can enable microstructure control in high-entropy carbides, yet quantitative grain-growth kinetics remain scarce. In this work, grain growth kinetics and densification…
The microstructure and mechanical properties of materials saturate to steady states after severe plastic deformation (SPD). Despite the well-known effect of temperature on the steady-state microstructure, there is no general agreement on…
High strength 7xxx Al-alloys are currently commonly used in aerospace and are expected to be increasingly employed in the automotive sector for weight reduction purposes. These alloys can however be sensitive to stress-corrosion cracking…
Tube processing and aging effects in FeCrAl ODS steels are investigated in four mechanical alloyed ferritic ODS steels, Fe15Cr (SP2), Fe15Cr5Al (SP4), Fe15Cr7Al (SP7) and Fe18Cr7Al (SP11). These steels were made into 0.3mm thick plates by…
In this paper, to improve wear resistance of components such as screws under severe friction-wear, Fe-Cr-C-Mo-V-Ti-N hardfacing coatings were further developed. The hardfacing coatings were acquired by shielded manual arc welding (SMAW)…
The mechanical behavior of two nanocrystalline Al alloys, Al-Mg-Y and Al-Fe-Y, is investigated with in-situ micropillar compression testing. Both alloys were strengthened by a hierarchical microstructure including grain boundary…
We use the phase-field method to study the martensitic transformation at the nanoscale. For nanosystems such as nanowires and nanograins embedded in a stiff matrix, the geometric constraints and boundary conditions have an impact on…
The diffusion-controlled growth and microstructural evolution at the interface of aluminide coatings and different substrates such as Ni-base superalloys and steel are reviewed. Quantitative diffusion analysis indicates that the diffusion…
We studied the structural and magnetic properties of \textit{in-situ} grown iron mononitride (FeN) thin films. Initial stages of film growth were trapped utilizing synchrotron based soft x-ray absorption near edge spectroscopy (XANES) at…
Recycled aluminum alloys are pivotal for sustainable manufacturing, offering strength, durability, and environmental advantages. However, the presence of iron (Fe) impurities poses a major challenge, undermining their properties and…
We report the chemical synthesis of Fe-core/Au-shell nanoparticles by a reverse micelle method, and the investigation of their growth mechanisms and oxidation-resistant characteristics. The core-shell structure and the presence of the Fe &…
A medium Mn steel of composition Fe-4.8Mn-2.8Al-1.5Si-0.51C (wt.\%) was processed to obtain two different microstructures representing two different approaches in the hot rolling mill, resulting in equiaxed vs. a mixed equiaxed and lamellar…
Homogenization is one of the critical stages in the post-heat treatment of additive manufacturing (AM) component to achieve uniform microstructure. During homogenization, grain coarsening could be an issue to reserve strength, which…
Additive manufacturing (AM) offers an unprecedented opportunity for the quick production of complex shaped parts directly from a powder precursor. But its application to functional materials in general and magnetic materials in particular…