相关论文: An economical in-class sticker microfluidic activi…
Optofluidic devices have revolutionized the manipulation and transportation of fluid at smaller length scales ranging from micrometers to millimeters. We describe a dedicated optical setup for studying laser-induced cavitation inside a…
Biomedical and biochemical processes in paper-based microfluidic devices often deal with mixing of two analytes to perform important functions. Uniform mixing of analytes in paper matrix is a challenging proposition, often necessitating…
The miniaturization and integration of electronic circuitry has not only made the enormous increase in performance of semiconductor devices possible but also spawned a myriad of new products and applications ranging from a cellular phone to…
Here, we describe a simple and unique architecture of a microfluidic mixer that can mix two streams (Water and Fluorescein Isothiocyanate (FITC) buffer) with 30% efficiency. The overall mixing in this design is dominated by 1D diffusion,…
Microfluidic mixing is a fundamental functionality in most lab on a chip (LOC) systems,whereas realization of efficient mixing is challenging in microfluidic channels due to the small Reynolds numbers. Here, we design and fabricate a…
Without any major changes, a pilot version of a physical science lab course was able to continue when the COVID-19 crisis necessitated the abrupt suspension of on-campus education. The 'Maker Lab' course, in which students conceive and set…
The micromixing process in microfluidic devices is of central importance in quite a few applications, with microfluidic studies on carbon capture and environmental monitoring being two examples. High surface area to volume ratio in…
Investigations of free-standing liquid films enjoy an increasing popularity due to their relevance for many fundamental and applied scientific problems. They constitute soap bubbles and foams, serve as membranes for gas transport or as…
Prior to macroscopic yielding, most materials undergo a regime of plastic activity that cannot be resolved in conventional bulk deformation experiments. In this pre-yield, or micro-plastic regime, it is the initial three dimensional defect…
Microfluidics have emerged as a vital tool in various scientific and engineering applications, ranging from biomedical diagnostics to chemical analysis. However, conventional fabrication methods often necessitate costly equipment and…
Mixing is one of the basic functions which automated lab-on-chips require for the effective management of liquid samples. In this paper we report on the working principle, design, fabrication and experimental characterization of a…
Optics is an important subfield of physics required for instrument design and used in a variety of other disciplines, including materials science, physics, and life sciences such as developmental biology and cell biology. It is important to…
Acoustic tweezers comprising a surface acoustic wave chip and a disposable silicon microfluidic chip are potentially advantageous to stable and cost-ffective acoustofluidic experiments while avoiding the cross-contamination by reusing the…
Effective mixing is essential for biochemical reactions. In droplet-based microfluidics, immediate mixing of substances upon contact in the droplet formation stage can greatly enhance the uniformity of chemical reactions. Furthermore, it…
We demonstrate a simple and cost-efficient scanning confocal microscope setup for use in advanced instructional physics laboratories. The setup is constructed from readily available commercial products, and the implementation of a…
We present a thermal activated solvent bonding technique for the formation of embedded microstrucutres in polymer. It is based on the temperature dependent solubility of polymer in a liquid that is not a solvent at room temperature. With…
Active fluids have applications in micromixing, but little is known about the mixing kinematics of systems with spatiotemporally-varying activity. To investigate, UV-activated caged ATP was used to activate controlled regions of…
Arrays of H-shape microfluidic channels connecting two different fluidic reservoirs have been built with silicon/SU8 microfabrication technologies utilized in production of thermal inkjet printheads. The fluids are delivered to the channels…
-- In this paper, a new approach to impart practical skill based technical education is presented in comprehensive manner. An Electronic Mini-Lab (EML) is devised containing basic design and test instruments with electronic components, ICs,…
Microfluidics involves the manipulation of flows at the microscale, typically requiring external power sources to generate pressure gradients. Alternatively, harnessing flows from active fluids, which are usually chaotic, has been proposed…