相关论文: Development of a 120-mm Aperture Nb3Sn Dipole Coil…

The stress-management cos-theta (SMCT) coil is a new concept which has been proposed and is being developed at Fermilab in the framework of US Magnet Development Program (US-MDP) for high-field and/or large-aperture accelerator magnets…

This paper presents the design concept of the dipole magnet with 50 mm aperture, 20 T nominal field and 13% margin based on a six-layer cos-theta (CT) hybrid coil design. Due to the high stresses and strains in the coil at high field,…

Magnetic and mechanical designs of a Nb3Sn quadrupole magnet with 120-mm aperture suitable for interaction regions of hadron colliders are presented. The magnet is based on a two-layer shell-type coil and a cold iron yoke. Special spacers…

This paper presents a design concept of an HTS/LTS hybrid dipole with 50 mm aperture and 20 T nominal field based on a cos-theta coil and a cold iron yoke. The HTS part of magnet coil uses REBCO Twisted Stacked Tape cable. The LTS part is…

Developing HTS dipole inserts producing fields larger than 5 T within 15 T Nb3Sn outserts is necessary to generate 20 T or higher fields for future high energy colliders. Dipole inserts based on the cos-theta coil geometry with various…

During testing of the Stress Managed Cosine-Theta dipole mirror magnet SMCTM1, magnet quenches were observed following large voltage spikes in the half-coil voltage taps which preceded normal quench initiation. Following some recent work at…

We report on the test of a small scale, non-planar coil using non-insulated ReBCO tape wound on a 3D-printed aluminum support structure. A 3D-scan of the winding frame which was printed out of AlSi10Mg using selective laser melting, showed…

The design concept of the Electron Ion Collider (EIC), which is under construction at BNL, considers adding a 2nd Interaction Region (IR) and detector to the machine after completion of the present EIC project. Recent progress with…

This work introduces the design analysis simulation and a standard MEMS fabrication process for a three dimensional microcoil with a magnetic core and a digital switch configuration using a completely integrated fully MEMS compatible…

New accelerator magnet technology based on Nb3Sn superconductor is being developed at Fermilab since late 90's. Six short dipole models, seven short quadrupole models and numerous individual dipole and quadrupole coils have been built and…

We present an analytic method to minimize the magnetic cross-talk in twin-aperture cos-theta dipoles. In the single-aperture cos-theta layout, the coil design can be performed with an analytic approach, based on a sector coil approximation.…

The conventional k.p method fails to capture the full and essential physics of many symmetry enriched multiple nodal line structures in the three dimensional Brillouin zone. Here we present a new and systematical method to construct the…

Hydrogen resist lithography using the tip of a scanning tunneling microscope (STM) is employed for patterning p-type nanostructures in silicon. For this, the carrier density and mobility of boron $\delta$-layers, fabricated by gas-phase…

This study presents the design, simulation, and experimental validation of a novel multimodal concentric surface coil for MR imaging, developed to achieve higher B1 field efficiency while maintaining low SAR for enhanced imaging…

The High Intensity Heavy-Ion Accelerator Facility is a new project in the Institute of Modern Physics. The dipole magnets of all rings are conceived as fast cycled superconducting magnet with high magnetic field and large gap, the warm iron…

We performed closed-loop lab testing of large-format deformable mirrors (DMs) with hybrid variable reluctance actuators. TNO has been developing the hybrid variable reluctance actuators in support for a new generation of adaptive secondary…

A prototype Secondary-electron Emission Monitor (SEM) was installed in the 8 GeV proton transport line for the MiniBooNE experiment at Fermilab. The SEM is a segmented grid made with 5 um Ti foils, intended for use in the 120 GeV NuMI beam…

Atomic spin sensors offer precision measurements using compact, microfabricated packages, placing them in a competitive position for both market and research applications. Performance of these sensors such as dynamic range may be enhanced…

FNAL and CERN are developing a 5.5-m-long twin-aperture Nb3Sn dipole suitable for installation in the LHC. A 2-m-long single-aperture demonstrator dipole with 60 mm bore, a nominal field of 11 T at the LHC nominal current of 11.85 kA and…

Two-dimensional (2D) SnSe is an emerging 2D material exhibiting intriguing properties such as ferroelectricity and nonlinear optical response. Here, high-quality single-crystalline SnSe nanosheets were synthesized via NaCl-assisted chemical…