相关论文: Oxide-stabilized microstructure of severe plastica…
The thermal decomposition behavior, the microstructural evolution and its influence on the mechanical properties of a supersaturated Cu Co solid solution with ~100 nm average grain size prepared by severe plastic deformation is investigated…
In this study, severe plastic deformation by high pressure torsion is used as a fabrication method for nanocrystalline magnetic CuCo alloys in bulk quantities. By subsequent isothermal annealing, phase separation of the supersaturated solid…
Bulk nanocrystalline materials of small and medium ferromagnetic content were produced using severe plastic deformation by high-pressure torsion at roomtemperature. Giant magnetoresistive behavior was found for as deformed materials, which…
In this study, a preparation route of Co-Cu alloys with soft magnetic properties by high-pressure torsion deformation is introduced. Nanocrystalline, supersaturated single-phase microstructures are obtained after deformation of Co-Cu…
Severe plastic deformation using high-pressure torsion of ternary Cu-based materials (CuFeCo and CuFeNi) was used to fabricate bulk samples with a nanocrystalline microstructure. The goal was to produce materials featuring the granular…
Initial powder mixtures of Cu, Fe and Co are exposed to severe plastic deformation by high-pressure torsion to prepare solid solutions. A broad range of compositions is investigated, whereas this study aims at the synthesis of soft magnetic…
This study systematically investigates the microstructural evolution of nanoparticle-based CuO, WO$_3$, and composite 'CuO-WO$_3$' thin films induced by their post-deposition annealing. The films were reactively deposited using a…
This work gives insights into processing and characterisation of bulk nanocrystalline FeCr materials. The investigated FeCr alloys, consisting of 30, 50 and 70 at.% ferromagnetic Fe and remaining anti-ferromagnetic Cr, are processed by arc…
A complex study of aging kinetics for both coarse-grained and nanostructured by severe plastic deformation Cu -- 2 wt% Be alloy is reported. It is shown that aging of a coarse-grained alloy leads to continuous formation of nanosized CuBe…
The mechanism of the evolution of the deformed microstructure at the earliest stage of annealing where the existence of the lowest length scale substructure paves the way to the formation of the so-called subgrains, has been studied for the…
In this paper, the oxidation-assisted dealloying (OAD) of Cu0.7Al0.3 films with different microstructures which were obtained by high vacuum annealing at different temperatures were studied using powder X-ray diffraction, field-emission…
We report on the non-trivial nanoscale kinetics of the deposition of novel complex oxide heterostructures composed of a unit-cell thick correlated metal LaNiO3 and dielectric LaAlO3. The multilayers demonstrate exceptionally good…
Zinc alloys have emerged as promising candidates for biodegradable materials due to their remarkable biocompatibility and favorable mechanical characteristics. The incorporation of alloying elements plays an essential role in advancing the…
Nanocrystals of indium oxide (In$_2$O$_3$) with sizes below 10 nm were prepared in alumina matrixes by using a co-pulverization method. The used substrates such as borosilicate glasses or (100) silicon as well as the substrate temperatures…
If metal surfaces are exposed to sufficiently oxygen-rich environments, oxides start to form. Important steps in this process are the dissociative adsorption of oxygen at the surface, the incorporation of O atoms into the surface, the…
The wear-driven structural evolution of nanocrystalline Cu was simulated with molecular dynamics under constant normal loads, followed by a quantitative analysis. While the microstructure far away from the sliding contact remains unchanged,…
The thermal stability of nanocrystalline (nc) Al has been studied by means of positron lifetime spectroscopy and X-ray diffraction (XRD), prepared by compacting nanoparticles under high pressures. Those nanoparticles were produced by the…
Mixtures of Fe and Cu powders are cold-compacted and subsequently deformed with severe plastic deformation by high-pressure torsion, leading to bulk samples. The dilution of Fe in the Cu matrix is investigated with SQUID-magnetometry,…
The paper presents a new approach, based on controlled oxidation of nanoscale metallic multilayers, to produce strong and hard oxide/metal nanocomposite coatings with high strength and good thermal stability. The approach is demonstrated by…
Monophasic and homogeneous Ni10Zr7 nanocrystalline alloy films were successfully grown at room temperature by co-sputtering in an indigenously developed three-gun DC/RF magnetron sputtering unit. The films could be produced with long-range…