相关论文: Proposed large scale monolithic fused silica mirro…
This paper presents an analysis of the conceptual design of a novel silicon suspension for the cryogenic test-mass mirrors of the low-frequency detector of the Einstein Telescope gravitational-wave observatory. In traditional suspensions,…
The use of fused-silica ribbons as suspensions in gravitational wave interferometers can result in significant improvements in pendulum mode thermal noise. Surface loss sets a lower bound to the level of noise achievable, at what level…
We report the mirror suspension design for Large-scale Cryogenic Gravitational wave Telescope, KAGRA, during bKAGRA Phase 1. Mirror thermal noise is one of the fundamental noises for room-temperature gravitational-wave detectors such as…
Current interferometric gravitational wave detectors use the combination of quasi-monochromatic, continuous-wave laser light at 1064 nm and fused silica test masses at room temperature. Detectors of the third generation, such as the…
We present a calculation of the maximum sensitivity achievable by the LIGO Gravitational wave detector in construction, due to limiting thermal noise of its suspensions. We present a method to calculate thermal noise that allows the…
A folded resonant Fabry-Perot cavity has the potential to significantly reduce the impact of coating thermal noise on the performance of kilometer scale gravitational wave detectors. When constructed using only spherical mirror surfaces it…
The suspension noise in interferometric gravitational wave detectors is caused by losses at the top and the bottom attachments of each suspension fiber. We use the Fluctuation-Dissipation theorem to argue that by careful positioning of the…
The design of new low-mechanical-loss, high reflectivity mirrors is crucial in the development of the next generation of gravitational-wave observatories. Currently, the state-of-the-art amorphous multilayer reflective coatings which are…
Grating reflectors have been repeatedly discussed to improve the noise performance of metrological applications due to the reduction or absence of any coating material. So far, however, no quantitative estimate on the thermal noise of these…
We study the thermal-noise spectrum of multi-loop pendulum suspensions for test masses in interferometric gravitational-wave detectors. The dependence of the thermal noise on suspension parameters and on properties of the wire material is…
We present the design, control system, and noise analysis of a 6-axis seismometer comprising a mass suspended by a single fused silica fibre. We utilise custom-made, compact Michelson interferometers for the readout of the mass motion…
The torsion pendulum is a prevailing instrument for measuring small forces acting on a solid body or those between solid bodies. While it offers powerful advantages, the measurement precision suffers from thermal noises of the suspending…
Multimaterial optical coatings are a promising viable option to meet the challenging requirements (in terms of transmittance, absorbance and thermal noise) of next generation gravitational wave detector mirrors. In this paper we focus on…
The thermal noise is expected to be one of the main limiting factors on the sensitivity of interferometric gravitational-wave detectors like LIGO and VIRGO. Thermal fluctuations of internal modes of the interferometer's test masses and of…
We present an interferometric sensor for investigating macroscopic quantum mechanics on a table-top scale. The sensor consists of pair of suspended optical cavities with a finesse in excess of 100,000 comprising 10 g fused-silica mirrors.…
Future gravitational wave detectors (GWDs) such as Advanced LIGO upgrades and the Einstein Telescope are planned to operate at cryogenic temperatures using crystalline silicon (cSi) test-mass mirrors at an operation wavelength of 1550 nm.…
Ground vibrations couple to the longitudinal and angular motion of the aLIGO test masses and limit the observatory sensitivity below 30\,Hz. Novel inertial sensors have the potential to improve the aLIGO sensitivity in this band and…
Interferometric gravitational wave detectors use mirrors whose substrates are formed from materials of low intrinsic mechanical dissipation. The two most likely choices for the test masses in future advanced detectors are fused silica or…
Seismic noise will be the dominant source of noise at low frequencies for ground based gravitational wave detectors, such as LIGO now under construction. Future interferometers installed at LIGO plan to use at least a double pendulum…
The gravitational waveform of merging binary neutron stars encodes information about extreme states of matter. Probing these gravitational emissions requires the gravitational-wave detectors to have high sensitivity above 1 kHz. Fortunately…