相关论文: Microstructure and wear resistance of Fe-Cr-C-Mo-V…
Cu-Sn-Zn coatings have been widely used in industry for their unique properties, such as good conductivity, high corrosion resistance and excellent solderability. To further improve the mechanical performance of Cu-Sn-Zn coatings,…
Lightweight refractory high-entropy alloy coatings (RHEAcs) of NbxMo$_{0.5}$Ti$_{1.5}$Ta$_{0.2}$Cr (where $x=$ 1, 1.3, 1.5, and 2) were fabricated on the surface of 316L stainless steel using laser cladding (LC) technology. A comprehensive…
Nanocrystalline metals are promising materials for wear-resistant applications due to their superior strength and hardness, but prior work has shown that cyclic loading can lead to coarsening. In this study, scratch wear tests were carried…
A theoretical-experimental methodology for failure analysis of the c-Al0.66Ti0.33N / Interface / M2 steel coating system is proposed here. This c-Al0.66Ti0.33N coating was deposited by the arc-PVD technique. For coating modeling the…
Wear resistant coatings were produced on a permanent mould cast MRI 230D Mg alloy by (a) PEO in silicate based electrolyte, (b) PEO in phosphate based electrolyte, (c) hybrid coatings of silicate PEO followed by laser surface alloying (LSA)…
While it is widely accepted that the steel-concrete interface (SCI) plays an important role in governing the long-term durability of reinforced concrete structures, understanding about the primary features of the SCI that influence…
Optical and electrical properties of two-dimensional transition metal dichalcogenides (TMDCs) grown by chemical vapor deposition (CVD) are strongly determined by their microstructure. Consequently, the visualization of spatial structural…
Hydrogen embrittlement can result in a sudden failure in metallic materials, which is particularly harmful in industrially relevant alloys, such as steels. A more comprehensive understanding of hydrogen interactions with microstructural…
This study focuses on the microstructure's evolution upon different aging conditions of a high-strength low-density steel with a composition of Fe-28Mn-9Al-1C. The steel is hot-rolled, subsequently quenched without any solution treatment,…
Room and high temperature mechanical properties of reactive magnetron sputtered TaSiN coatings were measured using nanoindentation (between 25C and 500C). Fracture toughness was also evaluated at a similar temperature range using the…
Chromium-based nitrides are used in hard, resilient coatings, and show promise for thermoelectric applications due to their combination of structural, thermal, and electronic properties. Here, we investigated the electronic structures and…
The introduction of nanostructured interlayers is one of the most promising strategies for interlaminar reinforcement in structural composites. In this work, we study the failure mechanism and interlayer microstructure of aerospace-grade…
Open-porous scaffolds of WE43 Mg alloy with a body-center cubic cell pattern were manufactured by laser powder bed fusion with different strut diameters. The geometry of the unit cells was adequately reproduced during additive manufacturing…
Grain boundary wetting as a preliminary stage for zinc induced grain boundary weakening and embrittlement in a Zn coated press hardened 20MnB8 steel was analyzed by means of electron backscatter diffraction, Auger electron spectroscopy,…
Ferromagnetic-ferroelectric nanocomposites are of interest for realizing strong strain mediated coupling between electric and magnetic subsystems due to high surface area-to-volume ratio. This report is on the synthesis of nickel ferrite…
A large body of literature within the additive manufacturing (AM) community has focused on successfully creating stable tungsten (W) microstructures due to significant interest in its application for extreme environments. However,…
Nanoparticles of Cr3+-substituted Ni-Zn ferrites with a general formula Ni0.4Zn0.6-xCrxFe2O4 (x = 0.0 - 0.6) have been synthesized via a facile microwave combustion route. The crystalline phase has been characterized by XRD, TEM, FT-I and…
Understanding the mechanisms of plasticity in structural steels is essential for the operation of next-generation fusion reactors. Elemental composition, particularly the amount of Cr present, and irradiation can have separate and…
An electro-chemo-mechanical phase-field formulation is developed to simulate pitting and stress corrosion in polycrystalline materials. The formulation incorporates dependencies of mechanical properties and corrosion potential on…
Total hip replacement is the most effective treatment for late stage osteoarthritis. However, adverse local tissue reactions (ALTRs) associated with fretting corrosion have been observed in patients with modular total hip implants. The…