相关论文: Simulation approach to reach the SQ limit in CIGS-…

In this paper we conduct numerical simulation of CdS/CIGS solar cells by use of the AMPS-1D software aiming to formulate the optimal design of the new multi-junction tandem solar cell providing its most efficient operation. We start with…

In this paper we study CdS/CdTe solar cells by means of AMPS-1D software. First we study the effect of thickness of semiconductor layers on the output parameters of the CdS/CdTe solar cell, such as density of short-circuit current, open…

In this paper we carried out theoretical study of the general issues related to the efficiency of SiC:H/a-Si:H single- and multi-junction tandem solar cells. Implementation of numerical simulations by the use of AMPS-1D program of…

We simulated photovoltaic characteristics of single heterojunction solar cell with Cu2ZnSnS4 and Cu2ZnSnSe4 absorber layer numerically using one dimensional solar cell capacitance simulator (SCAPS-1D). n-CdS/ZnO double buffer layer is used…

This paper proposes an efficient three-layered p-GaAs/p-CIGS/n-CdS (PPN), a unique solar cell architecture. Copper indium gallium selenide (CIGS)-based solar cells exhibit substantial performance than the ones utilizing cadmium sulfide…

In this article, we demonstrate CdSe-CuSbSe2-based double junction two-terminal tandem solar cells simulated with SCAPS-1D. The highest performance of the tandem cell has been confirmed by optimizing the electrical and optical properties of…

The p-type amorphous/ n-type crystalline silicon (P+ a-Si/N+ c-Si) heterojunction was simulated for developing the solar cells with high conversion efficiency and low cost. The characteristic of such cells with different work function of…

In spite of having higher carrier mobilities and absorption coefficients of germanium (Ge) than those of silicon (Si), there has been less focus on Ge-based solar cells due to the low bandgap and high-cost of Ge wafer as well as requirement…

A high theoretical efficiency of 47.2% was achieved by a novel combination of In0.51Ga0.49P, GaAs, In0.24Ga0.76As and In0.19Ga0.81Sb subcell layers in a simulated quadruple junction solar cell under 1 sun concentration. The electronic…

We develop a new approach to calculate the obtainable limit of photoconversion efficiency of tandem solar cells (SCs) and applied it to SCs with both vertical and lateral designs at AM0 and AM1.5 conditions. To get the maximum efficiency,…

A high photon to electricity conversion efficiency of 47.2082% was achieved by a novel combination of In0.51Ga0.49P, GaAs, In0.24Ga0.76As and In0.19Ga0.81Sb subcell layers in a quadruple junction solar cell design. The electronic bandgap of…

Solar modules are currently characterized at standard test conditions (STC), defined at 1000W/m2 and 25 {\deg}C. However, solar modules in actual outdoor operating conditions typically operate at lower illumination and higher temperature…

The purpose of this work is to look for a practical structure for application of quantum dots (QD) in solar cells in order to enhance sub-band gap photon absorption. We focuse on a stack of strain-compensated GaSb/GaAs type-II QDs. We…

Solar energy is the most convenient and reliable energy source among all renewable energy resources and an efficient photovoltaic device is required to convert this energy into utilizable energy. Different types of solar cells (SC) are…

The P+ {\alpha}-Si /N+ polycrystalline solar cell is molded using the AMPS-1D device simulator to explore the new high efficiency thin film poly-silicon solar cell. In order to analyze the characteristics of this device and the thickness of…

We present a model for simulating performance of 3D nano -coaxial and -hemispherical thin film solar cells. The material system considered in these simulations is hydrogenated amorphous silicon (a-Si:H), with solar cells fabricated in an…

Ternary chalcostibite copper antimony selenide (CuSbSe2) is a promising absorber material for next generation thin film solar cells due to the non-toxic nature, earth-abundance, low-cost fabrication technique, optimum bandgap and high…

CdTe-based thin film solar cell has been modeled and enumerated with a thin CuInTe2 (CIT) current booster layer. CdTe-based n-CdS/p-CdTe/p+-CIT/p++-WSe2 heterojunction device has been evaluated for the highest performance. It is revealed…

The power conversion efficiency of an ultrathin CIGS solar cell was maximized using a coupled optoelectronic model to determine the optimal bandgap grading of the nonhomogeneous CIGS layer in the thickness direction. The bandgap of the CIGS…

Single junction Si solar cells dominate photovoltaics but are close to their efficiency limits. This paper presents ideal limiting efficiencies for tandem and triple junction multijunction solar cells subject only to the constraint of the…