相关论文: A Comparative Analysis of Inconel 718 Made by Addi…
Previous research focused on two different mechanisms of microstructure stabilization in alloys: thermodynamic stabilization by reducing the grain boundary (GB) free energy and kinetic stabilization by suppressing the GB mobility by solute…
In this study, a preparation route of Co-Cu alloys with soft magnetic properties by high-pressure torsion deformation is introduced. Nanocrystalline, supersaturated single-phase microstructures are obtained after deformation of Co-Cu…
Hybrid Monte Carlo (MC)/molecular dynamics (MD) simulations are conducted to study the microstructures of nanocrystalline (nc) Cu/Ag alloys with various Ag concentrations. When the Ag concentration is below 50 Ag atoms/nm!, an increase in…
For the first time, cyclic re-austenitization is carried out for additively manufactured high-strength low-alloy (HSLA) steels in order to refine the microstructure by reducing the prior austenite grain (PAG) size. In this work, HSLA-100…
A microstructure-based model that accounts for the effect of grain size has been developed to study the effect of grain size on the fatigue life of Inconel 718 alloys. The fatigue behavior of two alloys with different grain size was…
The mechanism of the evolution of the deformed microstructure at the earliest stage of annealing where the existence of the lowest length scale substructure paves the way to the formation of the so-called subgrains, has been studied for the…
Correlated analysis of (sub)grains and particles in alloys is important to understand transformation processes and control material properties. A multimodal data fusion workflow directly combining subgrain data from electron backscatter…
Polycrystalline hcp metals - an important class of engineering materials - typically exhibit complex plasticity because of a limited number of slip systems. Among these metals, deformation is even more complicated in cobalt as it commonly…
In the present investigation, a strongly bonded strip of an aluminium-magnesium based alloy AA5086 is successfully produced through accumulative roll bonding (ARB). A maximum of up to eight passes has been used for the purpose.…
Co-doped BaFe2As2 has been previously shown to have an unusually significant improvement of Tc (up to 2 K, or almost 10%) with annealing 1-2 weeks at 700 or 800 C, where such annealing conditions are insufficient to allow significant atomic…
Microstructure evolution in metal additive manufacturing (AM) is a complex multi-physics and multi-scale problem. Understanding the impact of AM process conditions on the microstructure evolution and the resulting mechanical properties of…
Additive manufacturing (AM) enables the development of high-performance architected cellular materials, emphasizing the growing importance of establishing programmable and predictable energy absorption capabilities. This study evaluates the…
High strength steels are susceptible to H-induced failure, which is typically caused by the presence of diffusible H in the microstructure. The diffusivity of H in austenitic steels with fcc crystal structure is slow. The austenitic steels…
The effect of non-planar substrate surface on homogeneity and quality of cold sprayed (CS) deposits was studied by scanning acoustic microscopy (SAM). Fe coatings were cold sprayed onto Al substrates containing artificially introduced…
Molecular simulations have provided valuable insight into the microscopic mechanisms underlying homogeneous ice nucleation. While empirical models have been used extensively to study this phenomenon, simulations based on first-principles…
Microcompression testing is used to probe the uniaxial stress-strain response of a nanocrystalline alloy, with an emphasis on exploring how grain size and grain boundary relaxation state impact the complete flow curve and failure behavior.…
High-entropy alloys (HEAs) stand out between multi-component alloys due to their attractive microstructures and mechanical properties. In this investigation, molecular dynamics (MD) simulation and machine learning were used to ascertain the…
Solute segregation at low-angle grain boundaries (LAGBs) critically affects the microstructure and mechanical properties of magnesium (Mg) alloys. In modern alloys containing multiple substitutional elements, understanding solute-solute…
Nanostructures have the immense potential to supplant the traditional metallic structure as they show enhanced mechanical properties through strain hardening. In this paper, the effect of grain size on the hardening mechanism of Al-Cu…
Near-beta titanium alloys have shown low Young's modulus and good strength, making them excellent implant candidates. However, their processing using thermomechanical routes in single phase beta region results in heterogeneous…