相关论文: Direct synthesis of p-type bulk BiCuSeO oxyselenid…
We report on the direct ultrafast synthesis of Pb-doped BiCuSeO oxyselenides by high-energy ball milling. We show that, contrary to the mechanical alloying sintering routes used in the previous reports which require 7 - 13 hours to…
Among layered oxygen-containing compounds, BiCuSeO is one of the most promising candidates for thermoelectric applications due to its intrinsically low thermal conductivity and good thermal stability. However, the rather poor electrical…
Bulk p and n-type bismuth telluride were prepared using spark plasma texturization method. The texture development along the uniaxial load in the 001 direction is confirmed from both x-ray diffraction analysis and Electron Backscattering…
A high density CaKFe$_4$As$_4$ bulk sample was successfully synthesized using a spark plasma sintering (SPS) technique. The density of the synthesized sample was 5.02 g cm$^{-3}$, corresponding to 96.2% of the theoretical density of…
We optimize the superconducting properties of Sm-based oxypnictide (Sm1111: SmFeAsO0.80F0.20) by using the Spark Plasma Sintering (SPS) technique under various synthesis conditions, including heating temperatures ranging from 600 to 1000…
Thermoelectric materials allow the direct conversion of waste heat into electricity, and novel materials are being investigated for this purpose. Recently, doped Bi$_2$O$_2$Se has shown high application potential. In this study, we discuss…
High-throughput synthesis of bulk inorganic materials is crucial for accelerating functional materials discovery but is hindered by slow, energy-intensive solid-state methods. We introduce Direct Joule-Heated Synthesis (DJS), a rapid,…
We report an easy route single step synthesis of BiOCuS with and without Cu deficiency. The title compound is synthesized via solid state reaction route by encapsulation in an evacuated (10-3 Torr) quartz tube. Mixed components of the…
n-type Mg3Sb2-based compounds are emerging as a promising class of low-cost thermoelectric materials due to their extraordinary performance at low and intermediate temperatures. However, so far high thermoelectric performance has merely…
BaFe2As2 (Ba-122) and (Ba0.6K0.4)Fe2As2 (K-doped Ba-122) powders were successfully synthesized from the elements using a reaction method, which incorporates a mechanochemical reaction using high-impact ball milling. Mechanically-activated,…
Potassium tantalate (KTaO$_{3}$) is a promising material for dielectric applications at low temperature. However, dense and single-phase ceramics cannot be obtained by conventional sintering because of the evaporation of potassium that…
Two-dimensional (2D) bismuth oxyselenide (Bi2O2Se) with high electron mobility is advantageous in future high-performance and flexible electronic and optoelectronic devices. However, transfer of thin Bi2O2Se flakes is rather challenging,…
We report a solution-processed, ligand supported synthesis of 15-20 nm thick Sb(2-x)Bi(x)Te3 nanoplatelets. After complete ligand removal by a facile NH3-based etching procedure, the platelets are spark plasma sintered to a p-type…
Spark plasma sintering (SPS) technique is applied in combination with hydrogen decrepitation process for the recycling of SmCo5 magnets. The SmCo5 magnets for recycling were first decrepitated by hydrogen gas of a pressure of 4 bar for 3…
Hexagonal boron nitride (h-BN) is a brittle ceramic with a layered structure, however, recent experiments have suggested that inter-layer structural engineering could be key to new structural and functional properties. Here we report the…
We report a novel synthesis for near monodisperse, sub-10-nm Bi2Te3 nanoparticles. At first, a new reduction route to bismuth nanoparticles is described which are applied as starting materials in the formation of rhombohedral Bi2Te3…
A nanopowder from p-Bi-Sb-Te with particles ~ 10 nm were fabricated by the ball milling using different technological modes. Cold and hot pressing at different conditions and also SPS process were used for consolidation of the powder into a…
In this study, we demonstrate that introducing of rare-earth elements, $R$ = La or Pr, into the Bi-O charge reservoir layer of BiCuSeO leads to an increase of both, the charge carrier concentration and the effective mass. Although the…
The spark plasma sintering (SPS) process, a key technology for advanced material manufacturing, demands accurate and efficient simulation tools to capture the complex electro-thermal-mechanical interactions inherent in powder materials.…
Flash sintering is an approach allowing reducing the sintering time to mere seconds. To improve the microstructures and the properties of flash sintered specimens, this process has been successfully adapted to pressure assisted sintering…