相关论文: Measuring the length of stretched wires with a ava…
The single stretched-wire method is commonly used to measure the magnetic field strength and magnetic axis in an accelerator magnet. The integrated voltage at the connection terminals of the wire is a measure for the flux linked with the…
In many cases beam coupling impedances or wake fields are calculated with computer simulator such as CST Studio Suite, GdfidL Electromagnetic Field Simulator and so on. But evaluation with the stretched-wire method is still very useful by…
Coaxial wire measurements have provided a simple and effective way to measure the beam coupling impedance of accelerator structures for a number of years. It has been known how to measure the longitudinal and dipolar transverse impedance…
We present a novel electrical technique to measure the tension of wires in multi-wire drift chambers. We create alternating electric fields by biasing adjacent wires on both sides of a test wire with a superposition of positive and negative…
A scanning tunnelling microscope is used to pull a polythiophene wire from a Au(111) surface while measuring the current traversing the junction. Abrupt current increases measured during the lifting procedure are associated to the…
We explore the possibility of using free (as opposed to driven) oscillations to verify wire tension in large, open-frame multiwire planes. Using finite-element simulation we predict the signal when two wires are set in motion by applying…
A digital instrument that allows the measurement of the mechanical tension of an array of wires of known length and density, and the testing of their electrical continuity and isolation, has been developed. The instrument measures wire…
We present a new technique of direct measurement of wire tensions in wire chambers. A specially designed circuit plucks the wire using the Lorentz force and measures the frequency of damped transverse oscillations of the wire. The technique…
Both longitudinal and transverse coupling impedance for some critical components need to be measured for accelerator design. The twin wires method is widely used to measure longitudinal and transverse impedance on the bench. A mode error is…
Dipole wakefields in NLC (Next Linear Collider) structures have been measured with ASSET [1] and well predicted by a circuit model [2]. However, the experimental technique is both time-consuming and expensive. Here, we report on kick factor…
This work investigates the use of pulse stretching inverters for monitoring the variation of flux and Linear Energy Transfer (LET) of energetic particles. The basic particle detector consists of two cascaded pulse stretching (skew-sized)…
The coaxial wire method is a common and appreciated technique to assess the beam coupling impedance of an accelerator element from scattering parameters. Nevertheless, the results obtained from wire measurements could be inaccurate due to…
To study vertical sag requirements and factors affecting the stretched wire alignment method, the vertical sag equation is first derived theoretically. Subsequently, the influencing factors,such as the hanging weight or tension, span…
Accelerator magnets steer particle beams according to the field integrated along the trajectory over the magnet length. Purpose-wound coils measure these relevant parameters with high precision and complement efficiently point-like…
The traditional method to generate pulses in the range of some nanoseconds with high amplitudes, is the using of the avalanche-effect of transistors. However the problem with this method is the poor possibility for parameterizing. That was…
The coaxial wire method provides an experimental way of measuring wake fields without the need for a particle beam. A special setup has been designed and is in the process of being fabricated at SLAC to measure the loss factors and…
The optical fiber used as a microwave delay line exhibits high stability and low noise and makes accessible a long delay (>100 microseconds) in a wide bandwidth (about 40 GHz, limited by the optronic components). Hence, it finds…
The full characterization of a stringed musical instrument requires measuring the motion of the strings in at least two dimensions. Traditionally this has been done using electromagnetic means or by optical transmission. However in many…
Impedance measurements provide a useful probe of the physics of bolometers and calorimeters. We describe a method for measuring the complex impedance of these devices. In previous work, stray impedances and readout electronics of the…
In solving the Schr\"odinger equation to simulate a nanoscale circuit, we note that the mean free path for electrons in some metals is as large as 48 nm. Thus, the wavefunction may propagate coherently through wires corresponding to the…