相关论文: Basal slip of a screw dislocations in hexagonal ti…

A physically-informed continuum crystal plasticity model is presented to elucidate the deformation mechanisms and dislocation evolution in body-centered-cubic (bcc) tantalum widely used as a key structural material for mechanical and…

Defects play a key role in deciding the mechanisms and kinetics of phase transformations. In this paper, we show how dislocations influence phase separation in alloys with miscibility gap. Specifically, depending on the ratio of pipe…

Plastic deformation of metallic alloys usually takes place through slip, but occasionally involves twinning. In particular, twinning is important in hexagonal close packed materials where the easy slip systems are insufficient to…

Mechanisms that stabilize quasicrystals are much discussed but not finally resolved. We confirm the random tiling hypothesis and its predictions in a fully atomistic decagonal quasicrystal model by calculating the free energy and the phason…

A two dimensional amorphous material is modeled as an assembly of mesoscopic elemental pieces coupled together to form an elastically coherent structure. Plasticity is introduced as the existence of different minima in the energy landscape…

A new solution for general half-plane contact problems subject to a constant normal load together with alternating shear loads and tension in the steady state is presented. The method uses a formulation where a displacement correction is…

Two-dimensional (2D) layered materials hosting dislocations have attracted considerable research attention in recent years. In particular, screw dislocations can result in a spiral topology and an interlayer twist in the layered materials,…

The thermodynamic dislocation theory presented in preceding papers is used here to describe shear-banding instabilities. Central ingredients of the theory are a thermodynamically defined effective configurational temperature, and a formula…

Recently, a dislocation free deformation mechanism was proposed by Kiritani et al., based on a series of experiments where thin foils of fcc metals were deformed at very high strain rates. In the experimental study, they observed a large…

Reorientation of the segregation pattern of a binary granular mixture on a two-dimensional hor- izontally oscillating tray is numerically realized. The mixture consists of large-and-heavy particles and small-and-light particles, the…

The modest aim of this short article is to provide some new results for a screw dislocation in a functionally graded material within the theory of gradient elasticity. These results, based on a displacement formulation and the Fourier…

Disappearance of a stacking fault in the hard-sphere crystal under gravity, such as reported by Zhu et al. [Nature 387 (1997) 883], has successfully been demonstrated by Monte Carlo simulations. We previously found that a less ordered (or…

Metals with fcc structure may exhibit deformation twinning under specific conditions, which is an interesting but somewhat elusive aspect of their deformation behavior. It is well acknowledged that the phenomenon occurs through the…

Voids can limit the life of engineering components. This motivates us to understand local plasticity around voids in a nickel base superalloy combining experiments and simulations. Single crystal samples were deformed in tension with…

We use first-principles density functional theory to study the generalized stacking fault energy surfaces for pyramidal-I and pyramidal-II slip systems in Mg. We demonstrate that the additional relaxation of atomic motions normal to the…

Plastic flow in body-centered cubic (BCC) metals and dilute/concentrated alloys is governed by the motion of <111> screw dislocations, whose glide is often impeded by cross-kinks (jogs). While existing strengthening models typically treat…

We investigate the roles of spin and packing fraction on the dynamics of cratering when a solid projectile impacts a granular bed at different incident angles. For that, we carried out DEM (discrete element method) computations in which we…

Understanding the mechanism of martensitic transformation is of great importance in developing advanced high strength steels, especially TRansformation-Induced Plasticity (TRIP) steels. The TRIP effect leads to enhanced work-hardening rate,…

Dislocation slip is a general deformation mode and governs the strength of metals. Via discrete dislocation dynamics and molecular dynamics simulations, we investigate the strain rate and dislocation density dependence of the strength of…

A hybrid scheme between large-scale electronic structure calculations is developed and applied to nanocrystalline silicon with more than 10$^5$ atoms. Dynamical fracture processes are simulated under external loads in the [001] direction.…