相关论文: Asymmetrical precipitation on {10-12} twin boundar…

We report on a quantitative investigation into the effect of size and distribution of rod-shaped \beta' precipitates on strength and ductility of a Mg-Zn alloy. Despite precipitation strengthening being crucial for the practical application…

Although magnesium alloys deform extensively through shear strains and crystallographic re-orientations associated with the growth of twins, little is known about the strengthening mechanisms associated with this deformation mode. A crystal…

The effect of pre-ageing deformation on the size and distribution of beta-prime precipitates and subsequently on the resulting strength and ductility have been measured in a Mg-3.0at.%Zn-0.5at.%Y alloy. The alloy was extruded and then…

Isothermal ageing of plastically deformed Mg-Zn-Y alloys resulted in precipitation along {10-12} twin boundaries. The bulky precipitates formed had structures similar to those recently reported for the rod-like \beta' precipitates, but…

While lean Mg-Zn-Ca alloys are promising materials for temporary implants, questions remain on the impact of Zn and Ca. In this context, the precipitation in Mg-1.5Zn-0.25Ca (ZX20, in wt.%) was investigated upon linear heating from about…

Precipitation hardening, which relies on a high density of intermetallic precipitates, is a commonly utilized technique for strengthening structural alloys. Structural alloys are commonly strengthened through a high density of small size…

Plastic deformation of metallic alloys usually takes place through slip, but occasionally involves twinning. In particular, twinning is important in hexagonal close packed materials where the easy slip systems are insufficient to…

We consider the process of precipitation in binary alloys in the presence of mechanical deformation. It is commonly observed that mechanical deformation prior to or during precipitation leads to microstructure with excess defects, which…

In this work electron backscattered diffraction (EBSD)-assisted slip trace analysis and transmission electron microscopy have been utilized to investigate the interaction of basal dislocations with precipitates in the Mg alloys…

Understanding the composition evolution of grain boundaries and grain boundary precipitation at near-atomic scale in aluminum alloys is crucial to tailor mechanical properties and to increase resistance to corrosion and stress corrosion…

Contraction twinning in magnesium alloys leads to new grains that are misoriented from the parent grain by a rotation of 56 deg around the a-axis. The classical theory of deformation twinning does not precise the atomic displacements and…

An ultrafine grained magnesium alloy has been produced through room temperature high-pressure torsion (HPT) of solutionised Mg-1.35 wt.%Mn. Dynamic precipitation of nanometer-scale Mn particles occurred during deformation. These particles…

The mechanical properties of Mg-Al alloys are greatly influenced by the complex intermetallic phase Mg$_{17}$Al$_{12}$, which is the most dominant precipitate found in this alloy system. The interaction of basal edge and 30$^\text{o}$…

Magnesium (Mg) and its alloys hold great potential as an energy-saving structural material for automative, aerospace applications. However, the use of Mg alloys has been limited due to poor ductility and formability. Poor mechanical…

The mechanisms of dislocation/precipitate interaction as well as the critical resolved shear stress were determined as a function of temperature in a Mg-4 wt. % Zn alloy by means of micropillar compression tests. It was found that the…

Precipitation in Mg-Zn alloys was analyzed by means of first principles calculations. Formation energies of symmetrically distinct hcp Mg1-xZnx (0 < x < 1) configurations were determined and potential candidates for Guinier-Preston zones…

Deformation twinning is an important deformation mechanism in a variety of materials, including metals and ceramics. This deformation mechanism is particularly important in low-symmetry hexagonal close-packed (hcp) metals such as Magnesium…

The interaction between edge basal dislocations and $\beta$-Mg$_{17}$Al$_{12}$ precipitates was studied using atomistic simulations. A strategy was developed to insert a lozenge-shaped Mg$_{17}$Al$_{12}$ precipitate with Burgers orientation…

Twinning is an important deformation mode of hexagonal close-packed metals. The crystallographic theory is based on the 150-years old concept of simple shear. The habit plane of the twin is the shear plane, it is invariant. Here we present…

The cyclic deformation behavior of extruded Mg-8.5wt.%Al alloy with a conventional extrusion texture and a modified texture is systematically investigated by in-situ neutron diffraction and elastic viscoplastic self-consistent (EVPSC)…