相关论文: Improved Calibration of Instruments for Small Dire…
This paper presents a joint calibration scheme for voltage (V) and current (I) probes that helps resolve accurately voltage-current phase differences even when the difference is very close to $90^{\circ}$. The latter has been a major issue…
Inertial measurement units (IMUs) are used in medical applications for many different purposes. However, an IMU's measurement accuracy can degrade over time, entailing re-calibration. In their 2014 paper, Tedaldi et al. presented an IMU…
We present an updated calibration of the Swift/UVOT broadband ultraviolet (uvw1, uvm2, and uvw2) filters. The new calibration accounts for the ~1% per year decline in the UVOT sensitivity observed in all filters, and makes use of additional…
Unsupervised domain adaptation (UDA) has witnessed remarkable advancements in improving the accuracy of models for unlabeled target domains. However, the calibration of predictive uncertainty in the target domain, a crucial aspect of the…
We present a frequency modulation technique for calibration of the displacement actuators of the LIGO 4-km-long interferometric gravitational-wave detectors. With the interferometer locked in a single-arm configuration, we modulate the…
Input current estimation is indispensable in the sensorless control algorithms for the problem of power factor compensation (PFC) of an AC-DC boost converter. The system estimator design is challenged by the bilinear form dynamics and…
In this paper, we present a novel estimation and control strategy to balance a formation of discrete-time oscillators on a circle. We consider the case in which each oscillator only gathers noisy proximity measurements, whose range is lower…
Low-frequency resonances with low stability margins affect video bandwidth characteristics of power amplifiers. In this work, a non-connectorized measurement technique is presented to obtain the low-frequency critical poles at internal…
A Distortion Contribution Analysis (DCA) obtains the distortion at the output of an analog electronic circuit as a sum of distortion contributions of its sub-circuits. Similar to a noise analysis, a DCA helps a designer to pinpoint the…
Atomic force microscope (AFM) users often calibrate the spring constants of cantilevers using functionality built into individual instruments. This is performed without reference to a global standard, which hinders robust comparison of…
An AC susceptometer operating in the range of 10 Hz to 100 kHz and at room temperature is designed, built, calibrated and used to characterize the magnetic behaviour of coated magnetic nanoparticles. Other weakly magnetic materials (in…
Precise extraction of sinusoidal vibration parameters is essential for the dynamic calibration of vibration sensors, such as accelerometers. However, several standard methods have not yet been optimized for large background noise. In this…
A transimpedance amplifier has been designed for scanning tunneling microscopy (STM). The amplifier features low noise (limited by the Johnson noise of the 1 G{\Omega} feedback resistor at low input current and low frequencies), sufficient…
We introduce a new and quantitative theoretical framework for noise spectral analysis using a threshold detector, which is then applied to a superconducting device: the Cavity Bifurcation Amplifier (CBA). We show that this new framework…
Estimating the directions of arrival (DOAs) of incoming plane waves is an essential topic in array signal processing. Widely adopted uniform linear arrays can only provide estimates of source azimuth. Thus, uniform circular arrays (UCAs)…
Microwave linear analog computers (MiLACs) have recently emerged as a promising solution for future gigantic multiple-input multiple-output (MIMO) systems, enabling beamforming with greatly reduced hardware and computational cost. However,…
Atomic force microscopy is an important tool for characterizing surface acoustic waves, in particular for high frequencies, where the wavelength is too short to be resolved by laser interferometry. A caveat is, that the cantilever…
With the aim to optimize and test the method of acoustic detection of ultra-high energy neutrinos in underwater telescopes a compact acoustic transmitter array has been developed. The acoustic parametric effect is used to reproduce the…
We describe instrumentation for conducting high sensitivity millimeter-wave cavity perturbation measurements over a broad frequency range (40-200 GHz) and in the presence of strong magnetic fields (up to 33 tesla). A Millimeter-wave Vector…
To test and calibrate various detectors in nuclear and high energy physics experiments, a general purposed calibration instrument has been developed. All information including timing, amplitude and charge of signals can be directly obtained…