相关论文: Design of a 10 MeV normal conducting CW proton lin…

A proposal for a 10-120 mA proton linac employing superconducting beta-graded, CERN type, four cell cavities at 352 MHz is presented. The high energy part (100 MeV-1 GeV) of the machine is split in three beta-graded sections, and transverse…

The continue wave (CW) high current proton linac has wide applications as the front end of the high power proton machines. The low energy part is the most difficult one and there is no widely accepted solution yet. Both normal conducting…

In a long-term planning for neutrino experiments in China, a medium baseline neutrino beam is proposed which uses a CW superconducting linac of 15 MW in beam power as the proton driver. The linac will be based on the technologies which are…

In view of a possible evolution of the CERN accelerator complex towards higher proton intensities, a 2.2 GeV H- linac with 4 MW beam power has been designed, for use in connection with an accumulator and compressor ring as proton driver of…

A single gap, 352 MHz superconducting reentrant cavity for 5-100 MeV beams has been designed and it is presently under construction. This development is being done in the framework of a 30 mA proton linac project for nuclear waste…

Project-X is the proposed high intensity proton facility to be built at Fermilab, US. Its Superconducting Linac, to be used at first stage of acceleration, will be operated in continuous wave (CW) mode. The Linac is divided into three…

The accelerator for the APT Project is a 100 mA CW proton linac with an output energy of 1030 MeV. A High Energy Beam Transport (HEBT) conveys the beam to a raster expander, that provides a large rectangular distribution at a target/blanket…

The construction of the initial part of a normally conducting linac for hydrogen ion beams with a pulsed current of ~20 mA up to an energy of ~70 MeV is considered. The RFQ at a frequency of ~160 MHz accelerates ions to an energy of ~4 MeV.…

This paper reports on the feasibility study of a proton Super-Conducting Linac (SCL) as a driver gor the High-Flux Breader Reactor (HFBR) at Brookhaven National Laboratory (BNL). The Linac operates in Continuos Wave (CW) mode to produce an…

Front end of a CW linac of the Project X contains an H source, an RFQ, a medium energy transport line with the beam chopper, and a SC low-beta linac that accelerates H- from 2.5 MeV to 160 MeV. SC Single Spoke Resonators (SSR) will be used…

The CLIC linear collider aims at accelerating multiple bunches of electrons and positrons and colliding them at a centre of mass energy of 3 TeV. These bunches will be accelerated through X-band linacs, operating at an accelerating…

A superconducting (SC) linac is expected to lead to outstanding discoveries in various scientific fields because its beam current is a few orders of magnitude larger than in a normal-conducting linac. However, the widespread use of SC linac…

The peak current limit for the Fermilab Linac was recently studied. The purpose was to learn what components of the present Linac can be used for the first stage of a proposed proton driver[1]. For this application the Linac must provide a…

The China Accelerator Driven Sub-critical System (CADS) is a high intensity proton facility to dispose of nuclear waste and generate electric power. CADS is based on 1.5GeV, 10mA CW superconducting (SC) linac as a driver. The high-energy…

The higher efficiency of superconducting radio-frequency (SRF) cavities compared to normal-conducting ones enables the development of high-energy continuous-wave linear accelerators (linacs). Recent progress in the development of…

The conceptional design of the proposed linear electron-positron collider TESLA is based on 9-cell 1.3 GHz superconducting niobium cavities with an accelerating gradient of Eacc >= 25 MV/m at a quality factor Q0 > 5E+9. The design goal for…

The 1.7-GeV 100-mA CW proton linac is now under design for the Accelerator Production of Tritium (APT) Project. The APT linac comprises both the normal conducting (below 211 MeV) and superconducting (SC) sections. The high current leads to…

LINAC 4 is a normal conducting H- structure proposed to intensify the proton flux currently available for the CERN accelerator chain. This linac is designed to accelerate a 65 mA beam up to 160 MeV to be injected into the CERN Proton…

Spallation source dedicated for neutron scattering experiments, as well as multi-purpose facilities serving several applications call for pulsed mode operation of a high intensity proton linac. There is general agreement on the…

The article considers an opportunity of simultaneous pulsed acceleration of seven proton beams with current one hundred milliamps in each beam. The accelerator consists of two parts. In the first part of the accelerator having the length…