相关论文: Noise Performance of Lumped Element Direct Current…
We describe the performance of amplifiers in the 4 GHz--8 GHz range using Direct Current Superconducting Quantum Interference Devices(DC SQUIDs) in a lumped element configuration. We have used external impedance transformers to couple power…
We present measurements of an amplifier operating at 3.8 GHz with 150 MHz of bandwidth based on the microstrip input-coil resonance of a dc superconducting quantum interference device (SQUID) with submicron Josephson junctions. The noise…
To reduce the level of thermally generated electrical noise transmitted to superconducting quantum devices operating at 20 mK, we have developed thin-film microwave power attenuators operating from 1 to 10 GHz. The 20 dB and 30 dB…
Due to their superior noise performance, SQUIDs are an attractive alternative to high electron mobility transistors for constructing ultra-low-noise microwave amplifiers for cryogenic use. We describe the use of a lumped element SQUID…
The energy resolution of a single photon counting Microwave Kinetic Inductance Detector (MKID) can be degraded by noise coming from the primary low temperature amplifier in the detector's readout system. Until recently, quantum limited…
The fundamental noise limit of a phase-preserving amplifier at frequency $\omega /2\pi $ is the standard quantum limit $T_{q}=\hbar \omega /2k_{B}$. In the microwave range, the best candidates have been amplifiers based on superconducting…
Low-frequency superconducting lumped-element resonators have recently attracted significant attention in the context of axion dark matter searches. Here we present the design and implementation of a fixed-frequency superconducting resonator…
We demonstrate a lumped-element Josephson parametric amplifier, using a single-ended design that includes an on-chip, high-bandwidth flux bias line. The amplifier can be pumped into its region of parametric gain through either the input…
This paper presents the analysis, design, fabrication, and measurement of an integrated low-noise amplifier (LNA) implemented using a 130 nm CMOS technology, operating in the 2.4 GHz band. The LNA is a crucial component in the performance…
We report photon-noise limited performance of horn-coupled, aluminum lumped-element kinetic inductance detectors at millimeter wavelengths. The detectors are illuminated by a millimeter-wave source that uses an active multiplier chain to…
Low-noise amplification atmicrowave frequencies has become increasingly important for the research related to superconducting qubits and nanoelectromechanical systems. The fundamental limit of added noise by a phase-preserving amplifier is…
This paper describes the setup and the results of the direct on-wafer measurements of a FET noise parameters obtained with a source-pull method at temperatures down to T=4K and in the 5-12 GHz frequency range. The setup consists of a…
It has recently become possible to encode the quantum state of superconducting qubits and the position of nanomechanical oscillators into the states of microwave fields. However, to make an ideal measurement of the state of a qubit, or to…
We report on the total noise from an inductive motion transducer for a gravitational-wave antenna. The transducer uses a two-stage SQUID amplifier and has a noise temperature of 1.1 mK, of which 0.70 mK is due to back-action noise from the…
We investigate rf SQUIDs (Superconducting QUantum Interference Devices), coupled to a resonant input circuit, a readout tank circuit and a preamplifier, by numerically solving the corresponding Langevin equations and optimizing model…
Aluminum lumped-element kinetic inductance detectors (LEKIDs) sensitive to millimeter-wave photons have been shown to exhibit high quality factors, making them highly sensitive and multiplexable. The superconducting gap of aluminum limits…
We present measurements of 1/f frequency noise in both linear and Josephson-junction-embedded superconducting aluminum resonators in the low power, low temperature regime - typical operating conditions for superconducting qubits. The…
The present article primarily focuses on the design of an ultra-low-noise amplifier specifically tailored for quantum applications. The circuit design places a significant emphasis on improving the noise figure, as quantum-associated…
We have measured the quasiparticle generation-recombination (GR) noise in aluminium lumped element kinetic inductors with a wide range of detector volumes at various temperatures. The basic detector consists of meandering inductor and…
Accurate in situ calibration of microwave attenuation and amplification-chain noise is essential for superconducting quantum circuits. We demonstrate a compact, self-calibrating cryogenic noise source based on an on-chip chromium attenuator…