相关论文: Analytical Solution for BPM Reading the Multi-bunc…
The bunch-by-bunch BPM signal array has to be reshaped into a turn-by-turn (TBT) matrix in order to make the TBT beam position information of a single bunch available for further data analysis, such as via the Fourier transform to obtain…
The beam position monitor (BPM) system is of most importance in a light source. The capability of the BPM depends on the resolution of the system. The traditional standard deviation on the raw data method merely gives the upper limit of the…
The measurement of beam emittances by extracting the quadrupole mode signal from a 4 plate beam position monitor (BPM) was published at least 40 years ago. Unfortunately, in practice, this method suffers from poor signal to noise ratio and…
Beam position monitor (BPM) can easily reinforce the handling of beam orbits and measure the absolute beam position [1]. Its data can be used to optimize and correct beam in both first turn and closed orbit mode. In order to set the…
This introduction on beam position monitors (BPM) summarizes the fundamental parts of the tutorial presented at the CAS 2018 on beam instrumentation. The focus is on the signal detection and normalization, and on the principle of operation…
A system was developed for bunch-by-bunch detection of transverse proton and antiproton coherent oscillations based on the signal from a single beam-position monitor (BPM) located in a region of the ring with large amplitude functions. The…
For the PIP-II program, transverse emittance in the Fermilab Booster must remain well controlled at higher bunch intensities. 4-plate beam position monitors (BPMs) have a small but measurable quadrupole moment, making it possible to infer…
With a Bayesian Gaussian regression approach, a systematic method for analyzing a storage ring's beam position monitor (BPM) system requirements has been developed. The ultimate performance of a ring-based accelerator, based on brightness…
Coupled-bunch instabilities excited by the interaction of the particle beam with its surroundings can seriously limit the performance of circular particle accelerators. These instabilities can be cured by the use of active feedback systems…
A simple, analytically correct algorithm is developed for calculating pencil beam coordinates using the signals from an ideal cylindrical particle beam position monitor (BPM) with four pickup electrodes (PUEs) of infinitesimal widths. The…
In fast ramping synchrotrons like the Fermilab Booster the conventional methods of betatron tune evaluation from the turn-by-turn data may not work due to rapid changes of the tunes (sometimes in a course of a few dozens of turns) and a…
A high-precision intra-bunch-train beam orbit feedback correction system has been developed and tested in the ATF2 beamline of the Accelerator Test Facility at the High Energy Accelerator Research Organization in Japan. The system uses the…
BPM (Beam Position Measurement) system is one of the most important beam diagnostic instruments in accelerators. A fully digital BPM (DBPM) has been designed for SSRF (Shanghai Synchrotron Radiation Facility). As Analog-to-Digital Converter…
We show that properties of the beam position monitor (BPM) system designed for the measurement of transverse and energy beam jitters can be described in terms of the usual accelerator physics concepts of emittance, energy spread,…
Boosting is an extremely successful idea, allowing one to combine multiple low accuracy classifiers into a much more accurate voting classifier. In this work, we present a new and surprisingly simple Boosting algorithm that obtains a…
Certifying whether an arbitrary quantum system is entangled or not, is, in general, an NP-hard problem. Though various necessary and sufficient conditions have already been explored in this regard for lower dimensional systems, it is hard…
One of the main open problems in the qualitative theory of real planar differential systems is the study of limit cycles. In this article, we present an algorithmic approach for detecting how many limit cycles can bifurcate from the…
We present analytical results on the effect of pointing errors on the average bit-error probability (ABEP) of optically pre-amplified pulse-position modulation (PPM) receivers. The results show that the beam width plays a key role in the…
The problem of errors, arising due to finite BPM resolution, in the difference orbit parameters, which are found as a least squares fit to the BPM data, is one of the standard and important problems of accelerator physics. Even so for the…
The determination of beam parameters is essential for the operation and development of any accelerator facility. The working principle of frequently used beam instruments for electron and proton beams is discussed. The article comprises of…