相关论文: Rubber friction on wet and dry road surfaces: the …
Loss of braking power and rubber skidding on a wet road is still an open physics problem, since neither the hydrodynamical effects nor the loss of surface adhesion that are sometimes blamed really manage to explain the 20-30% observed loss…
We study rubber sliding friction on hard lubricated surfaces. We show that even if the hard surface appears smooth to the naked eye, it may exhibit short wavelength roughness, which may give the dominant contribution to rubber friction.…
We study the influence of the surface energy and contamination films on rubber adhesion and sliding friction. We find that there is a transfer of molecules from the rubber to the substrate which reduces the work of adhesion and makes the…
Rubber friction is of major practical importance in applications such as tires, rubber seals, and footwear. This review article focuses on the theory and experimental studies of rubber friction on substrates with random roughness. We…
We present a study of sliding friction for rigid triangular steel sliders on soft rubber substrates under both lubricated and dry conditions. For rubber surfaces lubricated with a thin film of silicone oil, the measured sliding friction at…
When a rubber block is sliding on a hard rough substrate, the substrate asperities will exert time-dependent deformations of the rubber surface resulting in viscoelastic energy dissipation in the rubber, which gives a contribution to the…
The modes of attachments, detachments and relaxations of molecules of rubbers and gels on solid surfaces are keys to understanding their frictional properties. An early stochastic model of polymer relaxations on surfaces was given by…
We study the sliding friction for viscoelastic solids, e.g., rubber, on hard flat substrate surfaces. We consider first the fluctuating shear stress inside a viscoelastic solid which results from the thermal motion of the atoms or molecules…
We generalize the Persson contact mechanics and rubber friction theory to the case where both surfaces have surface roughness. The solids can be rigid, elastic or viscoelastic, and can be homogeneous or layered. We calculate the contact…
This paper reports on the frictional properties of smooth rubber substrates sliding against rigid surfaces covered with various densities of colloidal nano-particles (average diameter 77 nm). Friction experiments were carried out using a…
We study the wear rate (mass loss per unit sliding distance) of a tire tread rubber compound sliding on concrete paver surfaces under dry and wet conditions, at different nominal contact pressures of $\sigma_0 = 0.12$, $0.29$, and $0.43 \…
In rubber friction studies it is often observed that the kinetic friction coefficient {\mu} depends on the nominal contact pressure p. We discuss several possible origins of the pressure dependency of {\mu}: (a) saturation of the contact…
Rubber wear results from the removal of small (micrometer-sized) rubber particles through crack propagation. In this study, we investigate the wear behavior of Styrene-Butadiene Rubber (SBR) and Natural Rubber (NR) sliding on two different…
We consider some basic principles of fluid-induced lubrication at soft interfaces. In particular, we show how the presence of a soft substrate leads to an increase in the physical separation between surfaces sliding past each other. By…
Tangential interactions between particles play a central role in suspension rheology. We show theoretically that these interactions, often attributed to contact friction, are a direct consequence of fluid flows between rough particles in…
We study the fluid squeeze-out from the interface between an elastic solid with a flat surface and a rigid solid with a randomly rough surface. As an application we discuss fluid squeeze-out between a tire tread block and a road surface.…
A huge number of technological and biological systems involves the lubricated contact between rough surfaces of soft solids in relative accelerated motion. Examples include dynamical rubber seals and the human joints. In this study we…
A theoretical model is proposed for low temperature friction between two smooth rigid solid surfaces separated by lubricant molecules, admitting their deformations and rotations. Appearance of different modes of energy dissipation (by…
Machine elements and mechanical components have often surfaces with anisotropic roughness, which may result from the machining processes, e.g. grinding, or from wear. Hence, it is important to understand how surface roughness anisotropy…
We study the average separation between an elastic solid and a hard solid with a nominal flat but randomly rough surface, as a function of the squeezing pressure. We present experimental results for a silicon rubber (PDMS) block with a flat…